Search results

can you take a picture at the doorway with the door open showing the about 90-100mm finished concrete to finished floor level ?? i also assume the fixings[nail or screws] are only at 600mm centres and thats the joist spacings ?? also worth checking if the bounce is through dipping rather than...

Suggest even basic research online will help you answer this question in my opinion, if you have to ask this question you have done zero research ??

general comments for future reference in a clad unpainted plank style shed in general the top will overhang all round a gutter is preferable so the water off the roof cannot bounce/splash/get onto the structure surface or underneath the walls and door should start protected at or near the roof...

i have ryobi power converters for both collecting solar energy and allowing tv' router other small charging needs like laptops and mobiles in power cuts https://www.direct-powertools.co.uk/ryobi-one-gen2-power-inverter-150w-18v-ry18bi150b-0-tool-only-c2x39903813

solent powertool spares seem to do loads off parts for the generic machines so worth a try they actually mention parkside

it doesnt really matter how you do it as long as the end off the felt is say 12mm clear off the timber to shed the water or the felt has to fold under and go uphill so the water drips off the low point

on a more practical note what ever height your decking is will detract from your permitted allowance for the summer house as in total permitted 2500mm decking at say 250mm your now restricted to 2250 on your summer house

general comments quite impressive the felt at the front should form some sort off drip clear off the doors and internal timbers as it is the water will tend to hang under the timber above the doors as it tracks round the felt as there is no place to fall off what would help is say a 19x38mm or...

i would say what ever you do i would think about either introducing drain holes in the metal or even making sure the gap is filled even with a slight taper off something like decorators caulk so the dropping water is diverted down the outside rather than getting trapped internally between wood...

other thoughts iff they are tongue and groove planks you may with the use off an undamaged plank be able to pair as long as you have at least 2 points on the tongue or groove to give parallel support to pass over a table saw but you would probably be cutting the inner edge off the damaged plank...

i have all the mentioned saws as in jig/band/track/circ/table and by default i use the table saw but as said by others you need a strait edge on at least one side if i had a specific job in mind i would reduce the planks to the length required with a say 20mm margin this makes the job much...

7x2 is the preworked stock size if its quoted in inches you need to reduce the size the machining will take off rough guide 1"= 21.5mm 2"=43mm 3"=69mm 4"=94mm 5" =119mm 6"=143mm 7"169mm you should always ask "what is the actual size" you should always measure the actual size a few inches...

another one for white board on the sides but just be aware if you want to fit a shelve with the 5mm shelve pins you must remove the say 3mm cladding thickness from the shelve length on one or both ends iff panelled both sides other options is fit the shelves first then clad between shelves...

whilst i am a great advocate for ryobi and have many off there worklights between around 100 to 3000 lumins i do NOT buy anything unless its around 40% off on line they are a closed shop with cbs power tools Peterborough as ryobi direct...

you can buy stepped double glazing for this exact purpose or you used to be able too you will need to alter the weighs or spring mechanism to accommodate the extra weight

i just use electrical tape that in its own right can help bind the load together or add protection from rubbing

as far as i know he is fine i dont think he would come back as an alter ego as he is strait-laced and like me has one tag on many forums he is also fully old school and open like me but he is far far older than me as i am 71 and a bit he is already 72:giggle:

a general guess if someone would take on the "bet" the odds would probably be perhaps 50/50 chance off approval so a margin off say 20% for profit so your cover would be 2500 plus 20% plus vat so perhaps £3600 if you can find someone interested which i doubt now they may deem the risk to be...

i wonder iff simply fully enclosing the handrail section and adding windows above with full double door all off which can be swung fully to 90% would then comply fully as no raised platform as its part off the internal floor and not a veranda as fully enclosed ??? just a though as a raised...

haven't updated my system since the original post so no updates i can give