Search results

It is 30min required in Scotland under 3 storeys. It's a copy and paste error, but how can I prove this to BC when she insisting on making the designer look like a **** making us protect it. In other words, where does it say beams in lofts are protected by the ceiling? Hugs for u woods there...

hi, I have an approved building warrant and a BCO that is being particular about regs and sticking exactly to the drawings. She also doesn't get on with the guy who drew the plans and this is adding to the fuss it seems. Steel is installed in the attic and protected by the ceiling, but on...

Turns out the bottom set relate to Climatic categories: 40/85/21 meaning= Minimum -°c / Maximum +°c / Damp Heat days I got this while looking through ebay listings but i guess it makes sense. It did fail when it was very cold, interesting. Thanks for your help all

Its a copy of a Karcher made by einhell i believe for Aldi. Do you think they would have used the same capacitor? The CBB60 seemed to bring up a lot of similar looking caps, the 45/81/20 doesnt seem to relate to its dimensions or anything. I guess its worth a punt buying the karcher one and...

Hi, My electric pressure washer hummed but didnt run and i remember a member talking about pumps and capacitors. I opened it and removed the big capacitor. Its a likely suspect :cautious: Im trying to find a replacement and wondered what the numbers on it actually mean. Its a push fit with...

(I'm not a pro) If I was setting out the tiles I would have made the corner look better, the small cut isn't ideal. Have they siliconed the corner or grouted it? Did they tile off the tray or but it against a tile? What did they do in preparation to the wall before tiling? just a thought...

Can I ask why?

When I did a similar beam in my house the same thing happened. It turns out to have the added bonus that stuff doesn't roll off onto the stove. I now call it an intentional feature... My beam also moved over time as the shakes opened up

Where would the dpc be in this picture? At the same height as the step or? To the rhs i thought the ground looked a bit high. No idea on the Tarmac I'm afraid(n)

Well i managed to get it apart and it cleaned up ok with brake cleaner. I was advised not to remove the muffler as it can cause problems with the reload mechanism. After lubing it, it feels better and fires fine :sneaky:

The pushrods and stem adaptor sit in the fan assembly and must do something with the gas can? They are easy to change so I bought them with origional o rings. The spark plug in my gun looks ok, but dirty. It is remarkably more dirty inside than I though it would be. Based on nothing I suppose...

I have an old but new to me paslode im350. It's seen better days and is filthy but fires. I'm planning on cleaning it up and replacing the o-rings. I have the correct oil etc. Is there any value in replacing the push rods and stem adaptor. I'm not even sure what these do but are offered in...

Could also be building back pressure in the fuel tank. If you open the tank and it fixes it for a while, the tank air inlet could be blocked Just a thought Graeme

Hi, I'm by no means an expert, but figure you may want to crack on with this. My experience with bin and 123 is to proceed to topcoat and I have had very good results with oil based satinwood on top of both. One could assume it's the same for cover stain and water based satinwood in the...

What's going on with the perps in the brickwork around the airbrick?

If it's close could you not use carborundum to file it a bit? There must be a way to file stone Just a thought Graeme

Thanks for that John I will tinker later today. So if it tune it up should I worry about engine rpm? I thought if I lean up the mixture I could over-rev it. The manual doesn't state it's max rpm, its not the best of machines... Thanks Graeme

I would be tempted to fit cat6 network cable in case I wanted to put in one later with a camera etc in it. Aside from that is it what type of cable or the actual where to run it your looking for?

Hi, Was hoping someone could tell me how to adjust the h jet properly on a mculloch hedge trimmer. I have a tachometer, but I'm guessing at where to tune it to. Spec sheet says max torque at 8-9k rpm, but it's running really rich at this speed with throttle wide open. Where would it be safe...

Thats a real mess, I hope you get that sorted and god knows what you will find in there. Still no digging out yet from my neighbour so we will see...