Search results

Thanks Johnny for your reply, I’m just clueless what to use to build it up eg mud or type 1 thanks Jake

Hi Johnny it’s 15cm not mm :)

Hi I’m just prepping the back garden ready for some artificial grass however levels are all over some large areas by 15cm too low …am I better adding some more soil whack it then my type 1 or have 15mm just of type 1? Thanks jake

I’d love to lay a concrete base however the shed is 15 square metres which is fine but to access the rear garden as we are a terraced we have to go through seceral Gardens to get to ours which means me with a barrow and doing all the mixing just wouldn’t work Lol

Hi I’m just about to start to lay my base for my shed/summer house thing anyway I need to raise the ground for the base by 30cm. What options do I have to keep my sub base in without collapsing at the sides. Concrete base is out. Thanks Jake

Thanks slawit will do… usually I use blue grit which if you haven’t used it’s fab stuff!

Hi I’ve got a project where I need to render it , I’ve currently covered it in tile backer board as it gives a really nice flat finish and I got it for free lol Anyway if I’m using a one Pocatello render can I skim this the same thickness as multi finish or would I still need the 10mm...

Hi Stevie, thanks for your reply, it was actually a very large bay window (3x1 ) which got rejected because no one else on the street has a roof( canopy) above their bay window line we have which seems crazy to deny it for that however rules are rules! It was just obviously going in front of...

Hi, Strange question but to cut a long story short I got my planning appeal rejected for a front extension. I know pd allows you to build a porch 3x1 but is there anything in the rules that stops you building two seperate porches 3x1? Thanks

Hi, I’ve got my little girls bedroom to re skim, I’ve already over boarded it and usually use a orange mesh tape which I’ve found great as it sticks well however our local Place only had white mesh joint tape in but it just won’t stick would there be any issues to use a bit of diluted pva to...

Evening, I’m hoping someone with a lot more experience in tiling can help me on this one ! I tiled our kitchen with 98x98mm flat gloss black tiles however due to renovation I need to extend the tiles however I just can’t seem to find these tiles anywhere, the closest locally to me is 98mm x...

Afternoon, I’ve had to cut some Slabs to use as coping stones 50mm thick concrete slabs, I just wondered what would be the best grinder disc To finish thecut Sides or other suggestions? Thanks Jake

Woody what I mean re plans is that the council expects a certain scale of plans etc before they will put them on the planning portal, the people who draw plans for a living wanted quite a lot which I’m happy I don’t have to pay lol

Lol thanks noseal, gives me some things to think about… I’m looking forward to this, I drew all my plans by hand and was a challenge because I had no idea however the next plans will be so much easier as I’ve leaned a lot, I’m chuffed they were good enough to be accepted and all it cost me was...

Hi I’ve just got my plans accepted for a small bay window and also got A building notice accepted for a small pd extension to the rear. The plans need to be still circulated in the community for people oppositions however I wondered if someone could tell me what things I’ll need to consider/...

Thanks guys for your help

Cheers thanks Taylor

Bel Ch602T re hob. Ideally using the same circuit for ease if it’s got to be hard wired, not sure why I thought it was a 13A I’ve not really looked at it as I’ve been installing some of the cabinets but I’m upto the oven housing now so sorting the wiring before the carcass is the right time...

Hi Taylor , Sorry I meant 32A, it’s just how the light caught the label yes it’s neutral , earth , l1&2 It’s a built in oven and hob both belling, The oven is a bl160fp, not actually unpacked that yet but I think it’s just a 13A switched fused spure but need to check. Not sure atm what model...

Hi, Would it be ok to use a 30A breaker on this? The cable looks to be 6mm? I was going to connect it to the current cabling which is 10mm to 30A breaker or should I reduce it to a 25A? I’m fairly confident that L1&L2 go together on a single phase but I don’t have so much pride that I don’t ask...