Search results

I am sure there is nothing in the instruction you will find to solve this problem. The most likely cause of a tv with this sympton is a electrolytic capacitor in the power supply which has gone faulty either leaking or going low capacitance taking a long period of time to charge to enough of its...

well Freddy me for one I spent 38 years as a TV field service technician for the three biggest rental companies and have seen hundreds of tv's written off over that time from strikes via mains sockets and aerial feeds and I for one will not risk my £800 plasma tv for the sake of missing ten...

well I am the one that is puzzled would you be kind enough to enlighten us all and explain your cryptic post

tockworth puzzled freddy

The vast majority of times a tv is knocked out during a lightning strike it is a write off with the at least the power supply fried I would advise anyone to completely isolate tv and other electronic equipment before a storm by pulling out mains plug from wall and disconecting any aerial or...

It depends on how much signal strength has been allocated to your feeder from the main building distributor. There is normally just enough to run one reciever per flat therefore you will almost certainly need at least a three way output signal amplifier connected at your original output point...

Small problem after installing IE8, now my remember id,s on this computer are not being stored. They do last at least one day so if I close the browser and re-open later that day they are stored but if I close down for the day then the next morning when I log on and open the browser all of...

glad to hear that and thanks for the feedback most people dont bother

Yes that should work I assume you are talking about a scart adaptor ie scart plug one end and double scart scart socket the other end.If that is the case you have to make sure it is a fully wired two way scart adaptor as some are just one way configured (the cheaper ones) that is it will input...

another also, if your signal to your tv is digital via a sky box or freeview box make sure the picture format settings on your sky or freeview box are set to 16:9 this is the wide screen picture format this would be on the menu settings of your digi box remote control

4:3 is the older picture format that suits the slightly older squarer tube tv's compared to the present current tv's now being produced which have a 16:9 format which is longer and narrower picture. It is the picture ratio dimensions

Possibly a setting go to menu and look for picture format settings it is possible it is defaulted on auto so if there is any old 4:3 stuff comes on it will change picture formats. You will need to set it to 16:9 and save or memorise that function.

can it really be beyond ecconomical repair have you not had an estimate from a repairer

If the generic remote control did not work there is a possibility that the TV has a fault on it. Modern power supplies in tv's when they develop a fault either in the power supply or the timebases will close down into standby automatically until the fault is rectified.This prevents the tv...

I Have just realised your model is a washer dryer not a washing machine and unfortunately whirlpool did make a range of washer/dryers were the front panel is not removable.All the fitting must be done through the door opening and the top of the machine fitting the inside first. If I remember...

If this is now an intermittent fault then the pressure switch could be a suspect. the pressure switch comprises of a small reservoir situated at the very bottom front of the tub from that a vertical plastic tube connected up to the switch itself. The switch has two states when the tub is empty...

yes that plastic ball is part of the machine and should be there. Electrolux is not a make I have worked on but if the brushes have plenty of life in them and the water is completely drained out of the tub before spin part of programme then it is time to be looking at other things starting with...

Yes brushes are suspect but check to make sure all water has drained from the tub as the programme starts spin mode. If it has not ( for example a partial or complete blockage in the pump/hose )the machine will not go into high spin.

take off or drop the kick plate at the bottom front of machine will expose two or three self tappers, remove these then hand each side of front panel pull down and off. You should have enough access to remove seal from tub end held on by band with securing screw at the top. reverse all steps to...

If the wma22 has the motor mounted at the top of the machine then stopping half way through a programme is an indication that the motor brushes need replacing