Search results

Thanks comments noted. How do I measure what size coving I need when it's in situ. I think from looking it about 100mm(4 inch). Also whats the best tool to use to shape the corner or would it be best to cut back from the right hand internal corner and fit a new internal corner piece using an...

Thanks for the reply. I had tried to fill in the right edge as seen in the photo before but didn't make too good a job. I didn't try to clean up the edge etc before hand. I will give it another go as it seems a sensible idea to follow. Will make sure I have a sharp stanley knife and a good...

The coving in my bedroom was damaged due to a leaking roof some years ago. It is now looking really bad and needs replacing. I think it is 4 inches (10 cm). Ideally about a nine inch section needs cutting away and replaced. I am useless when it comes to cutting mitres for coving plus it's...

Dan, you contributed to my post about the Honeywell DT92E. Set the TPi(Cr) to 3 but what does that actually does. If boiler limited to 3 cycles per hour what happens if stat is calling for heat? How accurate/sensitive is the DT92E. Yesterday I had it set for 22.5 & actual room temperature...

Thanks stem but I have managed to download the image and have checked I can load it into Paint on my W10 laptop should I need to amend it at anytime.

Thanks stem that's great, only suggested changing the thermostat A & B cable for terminals 3 & 4 if my grandson fits a new cable to keep things tidy. It may be awhile before I get him over but hopefully you will still have the plan if I need to make any changes. Incidentally, which software are...

stem thanks a bunch. Terminals 3 & 4 are currently as per your original (brown & grey). Unfortunately the cable to the receiver was only 3 core (black/brown/grey) and earth so although not right in order to get it working I used the earth cable for the live (which I have sleved brown) and black...

Hi stem Can I be really cheeky and ask if you could provide a revised wiring diagram showing the permanent 230V supply for the receiver, I followed you advice and used terminal (9) second from the left as the permanent live, and terminal (8) third from the left as the neutral. Having a full...

Think I may have partly answered my own question. Just noticed the relay was of again and also that the transmitter wasn't calling for heat. Whilst I wa watching the transmitter called for heat again and the relay led came back on......is that the correct operation?? Out of curiousity what is...

Hi, have installed the DT92E and it's working (sigh of relief) but will have to get my grandson over and tidy up the wiring as the airing cupboard is a bit of mess if I am honest. I hadn't noticed until mentioned earlier that the cable clamp hadn't been used due to my installing the junction...

Thanks

Looks like it will have to be a DIY job as my grandson is working so many hours he can't get over, but I think with the info I have received I should be OK, Just a couple of questions if I may. In his reply Dan Robinson said as I have an oil fired boiler not to forget to adjust TPi settings to...

Comments noted, another little job for the grandson when I get him here.

Thanks that's really great, even I shouldn't have any problem following things and I will make sure I keep a copy safe. I will heed your advice about terminals 6 & 7. Perhaps my grandson could tidy up the wiring when he comes over. How do I leave a thanks???

Ooops my mistake, forgot to number from the right.

Black terminal 5 (from the Horstmann Centaur) paired with brown to cylinder thermostat. The black wire from the boiler cable (with 3 rings) goes to terminal 2 and is paired with a brown from the Horstmann Centaur and the brown live mains. Hope this is clear as I have a problem bending down to...

stem The red on terminal 7 seems paired with an orange from the black Y Valve cable and a green/yellow (but tagged with red tape) from the tank stat. There is a black on terminal 2 which is paired as far as I can see with a brown from the Y Valve. Really appreciate your time and effort.

Can I get a wiring diagram for the Honeywell Y Valve v4073a1039 so I can make a note of the connections on the Honeywell Junction Box diagram. Forget that as I have found the info I need.

stem thanks for the very clear explanation. Before I start I am going to make up a full diagram of the Honeywell Junction Box so I can keep it with the other instructions etc. for the property. Can I get a wiring diagram for the Honeywell Y Valve v4073a1039 so I can make a note of the...

Echo the husky I have heat so that seems to have worked and at the moment nothing has gone bang! Will take a photo in the morning to keep as a record of the wiring or even make a diagram (won't get caught out again). Next step is to connect the new DT92E into the system. I have sufficient...