Search results

Yes! All smiles here. I'm alright with the wet side, it's just the leccy side i'm a bit unsure of.

OK, I returned the 711 and got a 522 or something. Looking at the instructions in the sealed box, there's a compatibility chart and the 522 has a direct exchange pin layout. I put it in, turned it on and it fires up. We have heat and hot water. Well, it's rising. Anyway, i opened the CP15...

OK, there's no power going to the CH motor pump. In the connection box that is by the pump + valve, there's power going into the valve motor and also going in and coming out of the tank thermostat, but nothing to the pump motor.

I forgot to say, i have a Drayton LP711 programmer here that I can use.

HI Board! I'm here to ask for your help, again. OK, we've had our kitchen fitted and the tiler finished yesterday. He went to put the programmer for our CH back onto the wall bracket and as he does, the thing goes POP, trying to spot weld itself to our ring mains. Black Smoke Of Dead...

Hi, My dad has done this with a huge deck and it's how i'm about to do mine. He compacted soil, compacted sand ontop of membrane and then set slabs into the ground in concrete. He then concreted a brick to the top of it and the internal points of the decking rest on those. Some big holes...

Hi Board, I hope you're all well. It has been a while since i last posted and i don't usually venture into the woodworking forum! I bought a Scheppach sharpening machine as i have loads of tools that i'd like to keep sharp. I assumed there would be some sort of guide in here, but there...

Thank you all for the detailed replies. I will check these over tomorrow. FYI - changing the motor did work, but then it stopped again shortly afterwards. It is intermittent though. I cannot find it, but i kept a log of what was doing what, and it never stayed the same for long! Part of this...

Hey, thanks for your reply. So, i should replace the micro switch in the unit? Or should i just buy a whole new unit? Thanks.

Hello Board! On the front bedroom window, there's been a bit of a drip for a while. It's actually coming through the top wooden portion of the window, like its leaking through the frame. It seems to appear there, leak all down inside the window, through the seal, back outside and down...

Hello Board! We have in the past, had some ongoing problems with our CH system that have resulted in several call outs and unfixed solutions. Recently, a lot of this came to a head and i decided to try and get to the bottom of what was going on. We have a Y system, cold storage tank in the...

Hello Board! I'm trying to put some sludge remover into my CH heating system via the F&E tank. I need to drain down a bit to get the gloop into the circulation. There's a very handy drain valve on the side of the little radiator in the bathroom downstairs. It's got a little point for a...

so i need 230v over the: White Grey and Orange wires? Do i just put the other probe to earth?

OK, 230v over White and Grey and 230v over White and Orange? This is the motorised part of the valve, the stepper motor, yes? Thanks again.

Yes - it is Honeywell

Sorry, the lever is turned by a motor which hits a microswitch that fires the boiler?

Hi, Thanks for your diagnosis. Would the manual lever be stuck itself, or would it flop around? Last time this happened, the lever was stuck so hard it would not move. We had the motor on the valve replaced and it worked fine. But this time, it is a little different. The valve moves...

Hello Board! I've had a few problems with our CH and HW systems over the last 2 years...We have an open system, Cold storage in loft, indirect tank in cupbaord, expansion feed tank in loft, 'T' valve etc. The rads only come on when the thermostat on the tank is calling for heat. When the...

All the cables are securely fixed to their screws. I also tried holding the unit to one side, incase the pins weren't making contact all along, but no dice.