Search results

Thanks - so that's thoroughly confused me! So I have connected the live, neutral and Earth in the connections included in the light as purchased. I have then connected the red loop wires into a single choc block. I wrapped the choc block in insulation tape as I heard this covers the live screws...

ThAnks - all in the same end an insulation tape wrapped round the block?

Just to check - do all 3 wires go in the same block - I assume so given they're not connected otherwise? Thanks in advance

Hilarious... Or not. That's predictive text for you! Thanks EFL - came up with an error on previous thread so didn't think it had posted. Thanks for advice though

Hi I've got a similar issue. I've changed a fair few ceiling roses but I've just bought a light with only 3 connections and I have a loop circuit. The live, neutral and earth wires are self explanatory but Any advice on what I do with the loop wires? Can I just buy a chic block 3 wire connection...

Hi I've got a similar issue. I've changed a fair few ceiling roses but I've just bought a light with only 3 connections and I have a loop circuit. The live, neutral and earth wires are self explanatory but Any advice on what I do with the loop wires? Can I just buy a 3 wire connection and...

Thanks for the replies. Unfortunately I put the old rad outside the house and it was taken so I'll need to buy a new one- this is all foreign to me - could you post a link to the exact product I need? I tried searching on screwfix for one but they only seem to do long ones which I assume isn't...

Hi I recently had a radiator changed in an upstairs bedroom and thought I'd use the one that was removed downstairs . I've tried to replace it, but that seems to be a piece missing that would screw into the radiator and over the valve. Can anyone tell me what the missing part is? I assume I can...

It is a typical tap - photo of tap and pipes under sink attached - no obvious valve though???

Thanks for your response. I don't think I'm up to it... Don't like messing with water... Any idea how much it should cost to get the washer changed? Thanks

Hi We have a real problem with our upstairs bathroom sink tap. Every time we turn it on and it starts to get hot water through it, it starts clunking really fiercely and the water comes out in spurts. If you turn the tap slightly either way it stops at clunking. We are running off a Worcester...

Anyone???

Hi I live in a victorian terrace house on a fairly steep hill in bristol. We've got a nice big kitchen we want to fit in a utility room and downstairs wc so are looking to extend into the side return. The side return is about 7m long and 1.3m wide with the boundary wall about 10ft high...

it looks to me like its just a case of plugging the Dt20 in though? should be simple enough? or am i just being overly optomistic??!

Hi I have recently had a Worcester Greenstar 28i bolier fitted. They were going to fit my existing controls with it (Danfoss FP715 two channel programmer and Honeywell wired stat) but when it came to it, the Danfoss Programmer they found that it wasn't compatible. So now we have the boiler...

What was the problem in the end? I have same problem with my Ideal Isar HE24 - leaking hot water from under the heat exchanger. The Heat Exchanger itself looks in good nick but there is water sitting in the tray beneath it which over time fills up and drips down out of the bottom of the boiler...

Hi We had the front of our house re-rendered and painted a few years ago. Despite the guy doing a mist coat and then a couple more coats its faded a lot (gets a lot of sun) and needs tidying up. I was looking to paint it myself but need a bit of advice: - there are no peeling bits - do I need...

so they came round and changed the auto air vent and a couple of other bits, puts pressure in the system and still leaking... They now say it needs a hydroblock and full A ring set... Shouldn't they have picked up on this on the first vist?

good suggestion but I'm a complete novice - is it easy to do? if so any step by step instructions would be appreciated!

The guy came round and it seems to be a leaking auto air vent. Problem is that it's going to be after the weekend till they can fix it and it's leaking on the PCB - It's switched off but still leaking. I asked the company and they said we'd just have to hope it doesn't damage the PCB. Is there...