Search results

Hi, I currently have a burger alarm fitted, and it is connected to my CU under "light" 5A fuse. The problem i have now, is I need to cut off the power on the "light" fuse to be able to change a light fittings on the ceiling. But as soon as I cut the power, the alarm sounds in my balcony. I...

ok, thanks for all the information :)

ic, so the best way is to cap it on the previous rad... but what happen if u duno which one is the previous one...... :oops: ?

I have a radiator in the bathroom which will no longer be used, should I put stop end cap on both in & outlet, Or should I make a connection in&out to keep the water flow back to the boiler to heat up?

corgigazza, I think you are right. I opened up the control unit, and here are the diagram : N L 1 2 3 4 1- HW OFF 2- CH OFF 3- HW ON 4- CH ON currently there are connection for N, L, 1, 3, 4 So what does it mean? How should I do to correct the wiring?

I am now thinking if its the boiler that causes the problem? because it just switched on ONCE from cold , then when the water is heated and CH is hot enough. It then switched Off and stays Off.... until the next program starts again from cold. On the timer theres HW override and CH override...

I have the similar problem as jezbo's problem. My radiator heated up then stop heating until the next start. I think the problem comes from the diverter (mid-position valve). It has W-M-H. When the central heating is just turned on, it switched to H. Then after it runs for a while it...

many good suggestion here, thank!

Thanks, Is UPVC easy to bend? cos I need to make it curve as well. :?

Hi, I bought shower enclosure W1200 x D800 mm. It is an offset "right hand" shower tray where it curved round one of the edge. as picture shown: click here However, the tray is only 100mm thick, and the waste cannot go all the way into the floorboards, therefore i need to raise it...

ic, so its better to keep it 15mm all the way i guess. is compression joint or push-fit joint stronger for a high pressure system?

Hi, I have a pump, and a shower mixer which I believe the pipe from pump to shower should keep it as 22mm. However the shower mixer Cold & Hot inlet is 1/2" (the inlet of the s-union with the chrome plates, then connect to 3/4" to the mixer) I need an elbow joint to connect from the...

Hi, I bought a high pressure mixer tap recently. Can I connect it to the pump? but then I assume there will be a short on & off on the pump everytime the tap is used + a vibration noise :S Will this harms the pump's life? Alternative is I guess to use the Cold from the Main, and keep...

Thanks ChrisR, i m still seeking more information and searching on the web. So how about a "Mixer Tap lever" for washhand basin, that connects the Cold to the main and Hot from the cylinder? Will that be problem too? sorry for so much questions, i just hope i can get as much as info as...

hmn... ic...So what is the alternative options to run the pipes? I already bought the 2 Thermostatic shower mixer and High pressure Taps (Grohe Eurodisc .http://www.plumb-warehouse.co.uk/ishop/968/shopscr242.html) please helppp :shock: :(

The problem is that my main pressure is not acutally that good... just enough to run a combi..(about 1~2 bar i remembered when a corgi came tested it). Therefore the shower wont be nice compare to having a 3 bar pump. So i guess having a tank feed + pump is my only options. :(

Thanks BAHCO, let me just confirm myself :oops: So you mean, run all COLD taps and WC from main. Hot taps will run from cylinder, not pumped. make extra pipe work to shower from Cold tank & Hot cylinder via a pump. Do you think my Hot water cylinder is too small? only a 36" x 18"?

yes, my tank is in the airing cupboard. The cold tanks is (HxWxD) 800mmx 600mm x 600mm (i dont know how many litres it can holds... sorry) The hot cylinder is a 36" X 18".

thanks BAHCO, because I m living in a flat. The Water tank is at my eye level. Thats y i m planning to fit a negative twin head pump. However, as i want to change all my existing taps to a higher pressure specification one, like a grohe mixer tap, therefore I want to fit the pump to the...

I wonder can I fit a 3.0 bar pump on the pipe where it just come out from the cold tank & and hot cylinder and feed it to the pipe where it goes to the bathrooms? so all the taps and shower mixer will be pressurised? Is that ok? can a tap be pressurised via a pump like this one?, and this...