Search results

Cheers all Lectrician, if I remember lrightly the MCBs are just like that in the photo as is the on/off switch legend. Coljack, the board has a smoked cover over the CBs just like that and also has the same label in the top corner just like in the picture. I havent seen the inside of...

Evening All A friend wishes to put an electric shower in to his property. I have informed him about BC etc but here goes. His house was rewired in 1984 and has two lighting circuits, 2 rings, 1 cooker and 1 immersion circuit. The CU is a Memera 21 with main switch and 2 spare ways, rated...

As far as it went for things like this I had a very "hush hush" attitude as far as speaking to my parents on these kind of things went. I couldn't imagine myself really talking to them much about these things. Personally I preferred it this way. I did though have sex education classes...

Hello Everyone A couple of things I have often thought about 1) Now that 1.5mm cable is normally used for lighting, but 1.0mm used to be used, if as an electrician you go to a domestic property to add an extra light and switch by breaking in to the lighting circuit, what size would you use...

Mine didn't! :shock: It just had the flex end stripped with copper crimped over the bare ends like appliance manufacturers often do when fitting plugs.

Cheers everyone The language used in the instructions doesn't seem good either since in some places it says 'live' an 'neutral' and others 'positive' and 'negative' (yes, referring to the mains supply conductors!). Despite it been ok on smaller loads, like I said I have seen some pictures...

This is exactly what I was thinking. I'm also not sure if it actually says which setting is the maximum for a standard plug settings 1-6. The machine is marked 30-135 amps i presume the output/ welding current? Powrcraft combination gas/no gas MIG welder purchased from Aldi. Yes I was a...

OK But would this actually be protected by a fuse or would a 32 amp mcb possibly type C, D etc be ok? (to install a seperate switchfuse, next to the CU, for the industrial type socket mentioned is not an option due to lack of space) Also is RCD tripping possible since I have heard welders...

HI My father has just bought a combination as/no gas MIG welder and am a bit confused about the supply. The instruction book in the begining says Model pcmig135/09 circuit breaker 30A. For Welding currents up to 65Amp (lower settings) a 13amp plug may be used and for above (higher...

HI Everyone Also I don't know if anyone's seen these but take a look..... http://wiki.diyfaq.org.uk/index.php?title=Changing_a_consumer_unit http://wiki.diyfaq.org.uk/index.php?title=Taking_electricity_outside Mind you though at least it's detailed and mentions part p etc. Regards

Read Step 4, How does the main switch on these flick itself into the off position when a fuse blows :roll: :? http://www.wikihow.com/Change-a-Fuse-in-a-Wylex-Standard-Fuse-Box Regards

Just had a thought: Seeing that many think these isolators after the meter pre CU are a good thing and some a bad thing, at least with a single pole isolator in the live only it MAY BE less likely to go wrong than a DP isolator since when these kind of things burn/overheat etc it is ALWAYS...

HI everyone, thanks for your advice. It is from a "Wiring and Lighting" 'Creative Do It Yourself' series published 1994 (ward lock). So if I needed to then would it be ok to add a triple socket as a spur? (say in a bedroom or sitting room) Regards

Thanks. But I have just looked again and as for adding sockets it says: "A spur can feed either one single or double socket. You cannot add a triple socket as a spur" But yet it mentions "triple sockets have an integral 13 amp fuse to protect from overloading". Just doesn't seem to...

Evening Everyone Why is it the case with the above, as it says in several do it yourself books? With triple sockets having a built in 13 amp fuse I would have thought this would limit the current drawn long before a 2.5mm spur would get get overloaded? Thanks

Evening Myself I would keep the RCD rule for all general use sockets and showers etc but would scrap the RCD 50mm rule (since I think it is one thing going a bit over the top) and the new alterations and extensions rule. I was just wondering what new regulations would everyone...

Just looked at the picture now. Again, the burning/overheating seems to have gone for the Neutral!!!

Oh well, after all, they are not an age restricted product regarding sales e.g in supermarkets, chemists etc. However a lot of people don't seem to know this since I have heard about young/young looking people been refused before (how embarassing must that be at a checkout in front of people...

OK Thank You

Please delete this post but NOT the whole topic. Regards