Search results

Hi, Doing a new restaurant job and the instruction for the fan and controller have gone walk about since i opened the box last week. i had a look when i had the books and matched the right diagram for the fan and controller as there are a lot of variations. wondering if someone can point me...

Sorry for the late reply and thanks for your comments. The tap is already permanently attached to the other end of the flexi's and doesn't unscrew as you would expect. I'm helping out a mate with fitting his bathroom and his dad acquired the tap from a site. the bars for the pop up...

Anyone tell me the preferred method for connecting to these. Only flexi's I've used before have just the standard tap connection. Thanks Martyn[/img][/i]

Sorry lectrician, your first post didn't come up when I looked last night. just the link to the manual. just been down to shop. I powered up last night and thought id just let it run with the fault on it. better than being off completely. so powered up and left presumed the beeping had...

Thanks Lectrician, Looks like I have to turn off the unused zones with the engineers access code but they have to start from 1. I want to remove zone 1. I suppose I will have to move zones 2 and 3 back to zones 1 and 2 and turn off 3 and 4??? anybody tell me if this is going to cause any...

Hi, I am an electrician and have just started a small shop job which will become a restaurant. rewiring and new fire alarm installed fairly recently. major works to the ground floor mean that I basically have to remove all of the wiring on that level and start again. 3 zones on the system...

Just finished first fixing a job like this. large lean-to extension with 21 down lights!! Wouldn't be my choice of lighting but the customer is always right eh! 150mm roof timbers to be filled with 125mm insulation spec'd by building inspector. customer suggested running cables, insulating...

So i'm officially compliant! NIC representative was a very nice bloke. wasn't fussed by the readings. He even said "who cares if you've got a 0.01, you've got a great earth path don't worry about your tester!!" You guys worry too much :D :D !! Didn't like my voltage tester which has...

so, wander lead resistance = 0.69 Ze test with wander lead = 0.69 Ze with standard lead = 0.01 So back up protection from the cut out fuse it is then! The supply transformer takes up a space which could have been a parking space or a single garage! that includes space around it. Its...

sorry too slow. i'll try it!

Im also not sure what your expecting me to do with a long lead? am I just being a bit slow! leads were nulled and checked and twice. it did read a 0.01 on one of the Ze tests!! The development is less than 10 years old and the supply transformer was installed at the time so im guessing...

Nothing like leaving it to the last minute ay? So NICEIC domestic installer inspection on Monday morning. 1st job to show is the work I've done at my own property! of course that means that until now I've not done anymore than the basics. r1 +r2 on the circuits I've touched and an RCD test...

I've had to do this a few times. Its understandable if the owner/ builder doesn't want to build a stud wall inside of the tanking. If nothing else it eats up space! I used adhesive, think it was pink grip but there is better out there. Needs to be quite stiff and fast setting so the boxes...

Not come across this before. Presumably a thermal cut out?? It's on the flow as it enters the megaflow. The zone valve is a sunvic which presumably works in a slightly different way. If anyone can enlighten me on this and why its like this I would be very greatful!!

Job done, spoke to the plumber and the customer again and there is some dispute as to who said it was a Y plan. I think it was a slip of the tongue by the plumber! 28mm valve was wrongly supplied by the plumbers merchant! could of had it done by 3.30 if I knew it was an S plan to start with!

fair point! Back to work for me then......