Search results

Sorry mate.. thought I had ..

Hi Sorry.. I'm struggling to find info on the 8xp jumper. There isnt any labels on the pcb. Or correct pcb layout in the manual.. its hardware revision 5. The only info on jumpers on expanders is that it's a star or daisy. But as I say it's not labelled. Cheers

cheers for the reply, Just to let you know i have sorted the issue now.. i changed the port range to forward and now works a treat.. ill be honest i was pulling my hair out as i knew it should of worked.. i didnt get any port conflicts when setting my port range.. anyway sorted now

hi , thought id post here . i have my ip cameras working fine within the texecom app on my internal network. so all good there. ive port forwarded within the router, thats the easy part, im struggling to figure out were i enter the external ip. does this go into the ip section next to Port (i...

Oh great.. I've done my best to segregate the cables. It is literally as they come into the panel.. Do you think throw a filter in for good measure

hello again, Im aware of ac induction within Alarm cables, is this something that you would pick up indefinitely if alarm cables are anywere near ac cables. im only asking because my 8 core alarm cables are all segregated away from ac , other than were i need to take them accross to the Elite...

Hahaha i thought that was 3 different settings.. appologies @secureiam . i think im the Bell now...

Im looking for this option also,rather than creating a new thread i used the search option, im using Wintex. i can find Bell on arm fail in Global options. but no Flashes if sets. panel is Premiere elite 24..

Thanks for the reply's. every day is a school day, so along with that.. Ill assume that with the Grade for insurance purposes it would also have to be installed by a Registered Engineer.

Hope someone can shed some light, im loooking round at alarm parts , panels etc. and i keep seeing that these items are Graded, Grade 2 , Grade 3 etc. can anyone tell me why this is and can these be mix and matched. could you have a grade 3 panel with grade 2 Pir's for instance? cheers in advance

sorry for the late reply, been alittle busy. thanks for the help buddy. appreciate it..

Cheers for the reply @sparkymarka , what would be your recomendations for wiring detectors? daisy chain or each on a single zone?

Hello all. I'm looking at fitting 4 detectors to my alarm system which is a texecom prem elite 24. Non richochet. Can any one recomend a particular detector. TBH been looking through. And installation manual says 2 wire detectors. And all I can find is 4 wire detectors. Hope you can help

brushless technology all day long for me. (y)(y)(y)(y)(y). 35% more power 5.0ah batterys last forever.. motor only uses what it needs under different loads.. have impacts combi sds and jig saw at the min. my mate has the 36v saw

anyone help with this? would be really helpful if i can leave the sink in

makita brushless 18v sds, apparently as good as its 24vnon brushless. i have one bought body only in macpak case 200 quid

can anyone tell me the max length of a needle.. ? i know its 900mm - 1200mm spacing.. im hoping i can get away with leaving the kitchen sink in , just to clarify needles will be about 1200mm long there are 4 but 1of them im wondering if i can make it longer.and put closer on the external side...

love the explanation,

no expert on this but heres my take . new build houses dont have air bricks and are pretty well air tight to meet regulations. your property will have draughts / ventilation all over id imagine. get your self a carbon monoxide alarm or 2 and block it up is what id do personnally. i reckon the...

yes , always right to left, (climb cutting on w/tops) same direction of the router bit into the edge..(keep a firm hold as it will want to run away bud, for instance for the left hand w/top edge youll flip the w/top updside down , and right hand top side up.. same as when your using the JIG...