Search results

what pressure do you put it to and can some one explain the procedure to me to make sure i get it 100% right, cheers simon

how should i contact baxi and what exactley should i say to them ?

ok i have pressured the system back to 1.5bar cold, then switched on the heating and th epressure has gone right upto 2.7bar. the bag over the prv has filled with water so that looks like where the leak is. 3 Qs: 1. Is the PRV valve easy to repair, what parts and where to get them. 2...

Just a word of note, not sure if this has been on here before but i have the above wireless room stat and timer and it has been causing me some right problems with my car central locking, the unit was placed near to the front of the house near to the driveway. It has been causing problems with...

Does the extra year waranty sound right ? sure i had some literature from Baxi once the installer had registerd it for me stating the 2 year warranty but i am unable to find it now, the installer also said it was 2 years.

where abouts is the relief valve ? is it the part next to the red twisty knob ? any diagrams to show me where ? if it is that is it an easy repair ? some one has mentioned that the noise from the rads could be the diverter valve, is this an easy repair ? any ideas of the cost of the parts ...

Ok iv had a Baxi 105 HE instant in for around 18mts now, the boiler came with a std 1 year warranty however as the installers were Baxi approved it came with a further year giving me 2 years warranty, over the last six months i have had to keep toppin up the pressure, and over the last week or...

ok will try that now i will pressure to 0.5 now and check again tomo, cheers

No water coming from PRV, any more ideas, if it is the vessel how much roughly to replace ? cheers

rads dont heat up at all, no drips from relief pipe, not sure where the auto air valve is, pressures rises around 1 bar. can you let me know where the airvalve is, the filling loop has been on since theye installed the boiler will this make any diffrence ?

Had the above boiler fitted a year ago, and have recently had to keep toping up the pressure, then when iv checked it today its down to .5 bar re pressured it up again to 1.3 without the pump going. I have checked all the rads and everyting is dry no loss anywhwere. Only thing i can think off is...

Thank god for that, you nearly give me heart attack was thinking i got a roight pile of @@@@ fitted till i read on, boiler seems fine aprt from this little problem which seems to have reset itself when i tunred the preheat back on. out of intrest how do you turn the flow rate up ?

hi, i had the above boiler fitted around 10 months ago, and the hot water was realy hot just lately the heat has dropped to hot but not too hot to touch like it was before, i think the fow rate has dropped a bit as well does this sound right ? what temp should the hot water be ? the rads are...

OK iv got it sorted at last, I found an old tub of Dulux oil based undercoat primer rollerd it on all the walls let it dry for 2 days, then covered it in Wilko's basecoat which was very very thick let it dry over 24hrs, then used crown matt emulsion and hey presto its sorted ! What a nightmare...

if you got to the point i have you will try anything, even naked skydiving if it would sort the damn crazing!

it was sugar soaped, then emulsioned. went on no probs has been ok for a year, wish i hadent repainted it now. matt on matt

really starting to get fed up now, after 6 coats of emulsion with various coats of other stuff between, ie pva bonder, sugar soap wash, jonsons acryl undercoat primer, all with a sanding down between. and still the crazing comes back, think im gunna go mad if i cant get it sorted soon. Please...

anyone else got any ideas ?

anyone else with any tips, where abouts this valve is and how to remove, and if it will cause any probs

Can the temp be turned down on this boiler and flow rate increased, when the system is on hot the rate is ok but the temp is very hot