Search results

thanks i will check it tomorrow as it has gone home for now can any body tell me how to test the locking motors if i take them off the car as i will take them off if needed the manual does not tell you how to test them off the car to see if they lock and unlock by connecting then to a battery...

cruisa i know it might sound a bit silly but have you tried pressing the reset after you have an alarm as this is the only way to stop the strobe flashing as it set like many alarms to tell you that you have had an alarm go off when you where out or in at the time if this stops the strobe by...

Hi all first time on this forum i usually go on the alarm side as i fit alarms and do diy mechanics good on engines and gearboxes body work ect but i have just purchased a 2000 reg zafira1.6 petrol for my daughter as the corsa was to small with 3 kids everything works great just fitted a...

Hi robbolooking at your post and i am almost certian it is the same as the old optima 6 you say you cannot find the manual on the ade honnywell site i have just been in and found the manual for the optima comact 6 user manual you need to go down the page and right clik on the optima 6 and open...

Hi i read your post on the gen 4 alarm and you definatly got a programing fault i fit these panels all the time and you need to slow down when programing it whilst in the engineers setup PRESS PROG THEN 1 THEN ARROW UP UNTIL YOU SEE INHIBIT THEN PRESS SET AND THEN YOU CAN SET EACH...

Hi kevintat glad you could understand my wiring diagram for your new passive if you shop around you will pick up some very small and discrete switches ideal for what you want as for the tamper light coming on when you put the engineers code in it must be an old G4 panel because the new one the...

Hi i can suggest that you go to the control panel and press PROG 9999 and see if the attack light is lit if it is then all you have to do is disconnect the electric supply to the alarm and open the panel without the alarm going off if the attack light is not lit then you will have to open the...

hi i read your post and cannot see why you have no power light on the L-C-D key pad have you got a power light on the control panel if not you will have to check the power supply to the panel and rectify if it is not lit you have a fuse inside the control panel and also should be fused on the...

HI I HAVE A SL8 USER MANUAL AND THE EXIT TIME CAN BE SET BY PUTTING THE ENGINEER CODE IN AND PRESS No 1== ZONE 1+2 SHOULD BE LIT AND YOU CAN ALTER THE EXIT TIME SO IF YOU WANT 10 SECONDS PRESS 01 IF YOU WANT 20 SECONDS PRESS 02 OR 30 SECONDS PRESS 03 AND SO ON [/img]

sounds like someone has set the tamper off press reset should stop the strobe but if the tamper light is still on the key pad will lock out until you find out why the tamper went off and rectify the fault either the passives if wired for tamper or the key pad tamper or the bell box tamper did...

SL8 ALARM MANUAL IF YOU NEED ANY MORE INFO LET ME KNOW

hi again has anybody got an optima compact 6 zone manual for a 2001 model i have reset it to factory conditions but need to program it for my garage i have the manual for the asscenta 8 mini and the G3 and the G4 L-C-D screen but none of them are compatible with the optima compact 6 zone some...

hi again reff my thread on 29 nov cold water header tank on the central heating blow off pipe permanently putting hot water back into the header tank we called the heatcall enginer out and he said it was a sticking valve which he said he fixed and put the top back on the header tank now we are...

Thanks every body for your quick response all worked ok and working fine to close to xmas to be without an alarm my daughter said thanks all. she can sleep at night know in her new house

hi all can anybody give me a reason for my central heating cold water tank is full of hot water causing a lot of condensation in the loft it apears to come out of the exspantion pipe blow off when the pump comes on it starts to feed water in to the header tank slowly but enough to make the...

hi all could anybody tell me how to factory reset an optima xm alarm panel if i remember right you conect a wire link to the right hand pa No 14 to set and power up the panel just want to make sure before i continue cheers every body have a nice xmas if i don*t reply before

HI ALL i just bought a all in one printer an epson dx 8400 but when i pluged it in there is no light on the pop up screen and no info to tell me what to do HELP

i suppose that you are familiar with the zone contacs on the alarm panel being closed circuit and also on the viper you have a closed circuit alarm contacts as well take 1 wire from one side of the zone you are wiring to on the control panel and take it to one side of the viper closed alarm...

yes you are probably right but it is for a freind because it was in the house when she bought it i am just getting it working until she can get an upgrade when she settles in cheers baz

thanks a lot guys got in touch with lynteck and now have the manuals thanks again chaps much appreciated baz :D hope that i can return the favour one day i work with ade and texicom and now honnywell very good panels very programable and reliable cheers baz