Search results

haha tell me about it :-) It's the yellow ADT box.....does that make any difference to the wiring at all?

As the title says I have an Accenta G4 panel and trying to connect my ADT (Elmdene) bellbox to it. Just fitted it all and all working fine apart from this problem. When I go to first power up the alarm and enter my code it silences the rkps but the adt bellbox carries on with the siren. There...

Yes good idea. Thankyou soooo much for taking the time and effort to help me out. So where is the button for a million thank yous.......or do I just have to sit here and keep pressing it :-)

The detectors are Exodus OH/4W. Just tried the detectors again and realised that the detectors do not sound....the sound comes from the sounder under the stairs.......that's why I thought only one detector was working as I was testing the upstairs one :-) Anyway I have disconected the sounder...

Ok just to clarify what I have done. From zone 8 black wire to first detector A. Then from first detector B black wire to second detector A. From second detector B blue wire straught back to zone 8. when I push the test button on the detectors only the second detector sounds. Gotta be a...

Sorry Alarm....haha obviously straight forward to you but you've gone and lost me totaly there!!! If you could maybe simplyfy it I may have a chance :-) I've put down the wiring colour I've used if that would help. Wires (red & green) from panels power to upstairs detector power. Wires...

Oh yes sorry makes sense. Wiring is as follows: Wire from panels power to upstairs detector power. Wire from panels power to downstairs detector power. Wire from panels zone 8 to downstairs detector A & B, from here wire goes to upstairs detector A & B.

Having problem with my smoke detectors connected to my Accenta G4 panel. The zone has been set as fire and all flags set as helpfully advised in an earlier post on here but when I push test button on detectors the 2 led lights up but no bells etc so I must have a wiring error. The...

I have 2 smoke detectors connected to my Accenta G4 panel, they are wired into zone 8. Have looked through the manual but cannot find in simple terms how to program the zone as fire alarm.

I have wired in the blue strobe to the strobe + and strobe - in the panel. To test the strobe i went into engineer mode/test outputs/strobe.......didn't work. I have since wired the 2 wires from the strobe light directly to the alarm battery and the strobe worked???? Have I wired the...

Fuse is ok....gonna try the strobe directly connecting to the battery to test it as bought it a while ago and it's been sitting in the garage. So am I right wiring it to the strobe + and - ?

I've got an Accenta Gen 4 and want to wire a blue strobe light to it, the light has got just 2 wires from it, I've wired it to the strobe + and - but not working. Any ideas?

There was 2 zones in p1....front contacts and back door contacts. I have removed the link from PA and joined shorting wire from the left PA to SET (nothing was wired in SET) Dont know what you mean by link out all the zones? 'By the way...thankyou for taking the time to try to help me :-)

Right.....I've now taken all the pirs out the equation by unwiring them and have also changed their zones to unused in all 3 programs....now if I go into the walk test the unused zones are all showing 1. The zones that have door contacts are zero and change when I activate. Is this correct so...

Thankyou Redsparky....that's got rid of the tamper fault lockout message now.. Now if I go into the engineer mode and select walk test instead of the zones being all zeros until i walk round and activate them they are 1s except for the two door contacts. Any ideas.....I have read and re-read...

Not really sure what you mean by tampers in series.....I have run cable from each pir and contact seperately to the panel and all the tamps go to the tamp connection in the panel. The bell has not been wired in as yet. I do not have a meter to get a reading.

Please excuse the long story but feel I should give you the full story to make it easier to help me with the problems I am having. I have an Accenta G4 with 2 remote lcd keypads. The system has the following zones wired: 1. Front hall pir 2. Rear hall pir 3. Living room pir 4. Back door...

What!!!......am I not allowed to post on more than one site then......for your information I posted on here first. I post on forums for help.....seems lately I get more replies with absolutely no help at all

Hi I am in the middle of fitting an intruder system.....all the pirs, contacts etc are connected and the 2 smoke detectors are ready to be connected. I still have to connect the external bell box, internal speaker, but if I get any problems with them I know where to come later. The control...

Fire is from Ekofires..........