Search results

  1. A

    Top Hung UPVC Window Hinges replacement

    Hi all I need to replace 11" top hung UPVC window Hinges but they seem to be unavailable anywhere. Could I use 12" and if so would I align the new with the top or bottom of the old hinge or make it equal ie place 1/2 inch each of either end of the old. TIA Steve
  2. A

    Hob cable in prescribed zone

    Yes, around the bottom is probably better thinking about it. thanks. Can I run a cable up to the hood from the hob connection box?
  3. A

    cupboard lighting FCU above kitchen cupboards

    I was going to use a kinetic switch.
  4. A

    Hob cable in prescribed zone

    Thanks for the responses. I hope this image makes it clearer.
  5. A

    Hob cable in prescribed zone

    Sorry should have said, unfortunately its on a different worktop/wall with a gap between them (although with 2m)
  6. A

    cupboard lighting FCU above kitchen cupboards

    Hi all To make things look neater I'd like to move an FCU for kitchen under cupboard lighting from next to a socket up to the wall above the cupboards (and therefore out of sight). Is this allowed under regs?
  7. A

    Hob cable in prescribed zone

    Hi all I want to change a gas hob to electric. The Main oven isolator switch is above a nearby worktop so I 'd like to run a 6mm cable up from this along the top of the wall in the permitted zone and then down by the hob to a connection unit behind a base uinit. The wire will go vertically down...
  8. A

    What paint for sliding mirrored doors?

    Hi all, I need to paint the surrounds of some bedroom mirrored doors. The edges are currently wood effect which I want white. I've put on an undercoat but am note sure which paint would be best on top as it will obviously be touched a lot to open and close the doors. I was going to put on a wood...
  9. A

    Wiring Nest to Glo Worm 30CXi boiler

    Thanks for the info everyone. Belated photos attached. The mains in is the white whire and seems to terminate at the on/off switch at the front of the boiler (ie behind the PCB)
  10. A

    Wiring Nest to Glo Worm 30CXi boiler

    Has any one wired up a Nest Heat Link to a Glow Worm 30CXi boiler. I've bought the nest and am very happy doing electrical work (although I know nothing about how a boiler works). Looking at the electrical diagram I thought it would be straight forward but have to say I'm really struggling. I...
  11. A

    CT / PG difference

    They are level, it’s just the camera picture shows distorted. Yes, I agree that they would have looked a lot better at the same height and a matching design but that’s how the metal back boxes were previously installed and that was the only design I could find incorporating a FCU/13a combo...
  12. A

    CT / PG difference

    Photos as promised...
  13. A

    CT / PG difference

    Will do, have just ordered one so will be next week sometime.
  14. A

    CT / PG difference

    Ah, thanks Rocky ...seems obvious now!
  15. A

    CT / PG difference

    Hi all I need to buy a RetroTouch Switched Fused Spur with 13a Unswitched Socket CT White 01102 as per the below: http://www.ebay.co.uk/itm/RetroTouch-Switched-Fused-Spur-with-13a-Unswitched-Socket-CT-White-01102-/292219279337 You can also buy one which looks identical but says it is...
  16. A

    Front door replacement seal

    Thanks for the link Jadele, thats exactly what I need!
  17. A

    Front door replacement seal

    Hi all I'm trying to find a replacement seal for the bottom of my front door similar to the attached image. I'm not sure if I need just the rubber or the whole unit but despite extensive googling can find neither. Could anyone advice please? TIA
Back
Top