Search results

tapping the relay can sometimes free it but if its 'welded' on good then no. the machine will need to be on whilst doing this so be careful not to touch any of the connections. you can test it yourself quite easily. let me know the markings on the relay in question or a photo of the relays...

get the whole machine replaced, you will have nothing but trouble with it! normally it would be due to a dirty or worn seal on the condenser; sometimes the condenser glue seal fails causing this but i suspect yours is caused by a defective housing and the condenser is not seating properly. if...

its possible the drain pump relay is jammed causing it to stick on the drain function

if the pressure sensor is testing good are you sure its not the mainboard interpretting the data incorrectly? might just be coincidence it worked again after blowing into it. Wiring continuity checks ok does it? connections all clean and making good to the pins? solder joints on the mainboard...

Recommended fixings to fix a pitched (front gable) porch canopy and gallow brackets to a brick and block cavity wall. The gallow brackets are 765mm high x 560mm deep (4" x 2") and will be fitted approx 2m apart. The canopy is 2.3m long x 580mm deep with approx a 25 degree pitch, constructed...

Its not within 2 metres of a highway so up it goes! Thankyou very much, puts my mind at ease knowing there won't be any issues. However, everyone else in our secluded area of 6 houses all have pitched porches from front to back, i.e front of porch back to the house wall whereas ours will be...

Can I fit a porch canopy in an AONB (Not in a conservation area) without planning permission? Do I need to even involve planning or any other governing 'body' of our intentions? Gallow brackets with canopy sitting on top. 'Floor area' size approx 600mm deep by 2.3m wide. Also, overall height...

You should be able to test whether the pressure switch is functioning or not. If its ok the board then needs further investigation or replacing.

Could prove useful for future readers what the rating of the resistor you replaced it with is? ohms and wattage It is also worth noting that cleaning as much of that 'soot' of as much as possible is a very important step as it can be conductive and enable current to short across to other components.

Is that just banging the front fascia or banging and jogging the whole machine? There are many things this could be from your description so more detail is needed. A more common fault based on your description would be a loose or dirty/corroded connection. With the machine unplugged disconnect...

F11 Error displayed on LCD. No indicator lights illuminate. Buzzer alarms to indicate fault condition. Have gone through and checked sensors, stats, heating element, pump etc.. etc.... and have come to the conclusion that the main control board is at fault. Anyone able to help troubleshoot the...

Thats fine. Stick it on gumtree free to collector, sure someone will collect it and get it out of your way for nothing!

Power off machine and disconnect from mains. Tip the machine on its back, careful not to break /bend / split the inlet hose or waste hose. There should be an access panel underneath, the float / switch etc is attached to the top side of this access plate. Its possible either: 1. The switch has...

Is there a 'Cancel' button, try this first then select a programme again. What happens? Then try a rinse only programme. What happens? Check drain pump, waste hose and sink 'U' bend(or wherever the waste hose connects) for blockages. Probably make sense to work your way back from the 'U' bend...

Does it empty the tub if you put a couple of cups of water in it then start a programme? It may be necessary to cancel the previous programme first.

Is there a dome inside the tub at the bottom near the bottom spray arm? Any flooding on the floor or inside the machines base? Might only be able to access necessary parts by removing from unit housing. Make and model?

Could be the new element faulty, unlucky! But it does happen. Whats the make & model of oven? Sure theres only one oven element??? Sometimes one in the base as well as at the back near fan.

Voltage reading across valve? Test the relay, let me know if you don't know how.

What reading did you get at the valve? Could just need a new relay soldered on pcb, about £2 if you can solder.

Is the door switch / mechanism actually working? Need to prove this first. As your aware you will have lights etc and be able to change the wash cycle on the top panel with the door open or closed. That is of course providing the on/off button is in the on position as it is showing in your...