Search results

Sorry. Its early. Thanks Madrab

Hi I will be installing my shwer screen this weekend. I have gone for the channels fixed to the floor and wall with a glass panel. Am i right in thinking that the installation method for this is; 1) Silicone the underside of the channels and mechanically fix to tiled floor and wall 2) Pump the...

I had aplumber in yesterday doing some other work. He re filled the system and it seemed to be working last night when i got home with noticeable heat coming into the rooms with UFH where they had been very cold before. Glad that the system seems to be working BUT the flow meters are still...

Ok I will refill myself and hopefully all then works

This looks like what the pipe installer did. He filled it and left it under pressure a few weeks back. Could it be that air has made its way round and needs topping up or do I need to re fill in the same way?

Thanks everyone. There are 3 loops on the left hand side that are yet to be installed and are blanked off (as i am still working in these rooms. The UFH company will commission it when these are complete but i want to get some heat in the house now on teh loops that are installed. The meters on...

I now have the UFH connected so that when the stats call for heat, the pump starts and the boiler kicks in. I have the temp set to 45' on teh mixer and the temp guage is showing just over 40' so that all looks good. The pressure gauge is showing circa 2 bar so also good. I set up all the...

The UFH should be up and running tomorrow. I had temporerily hooked it up to check it was all working and all seems good. I have a large cold area that has sat unheated since the extension began. I assume this will take several days to heat up. What is the best way to introduce heat into the...

After what seemed like a week of back and forth to the local tip, the house looked a lot clearer and i called in the UFH company to run the pipework and connect the manifold. To prevent cutting excessive runs into the UFH board to route the flow and return for 10 loops back to the manifold in...

I had a week off working on the house after firing a nail through my finger installing the last batten to a joist. Tiered, rushing and thinking everything was going ok, this was a very strong reminder of how easy it is to go horribly wrong. Back to work and it was the painful and long task of...

Its taken some time but i finally got the house fully rewired. Or at least to the point where all circuits were in even if final fittings etc were not there. Electrician came in a connected the new consumer unit. It has something i have been looking forward to as i now don't have a room full of...

I have always had separate wastes for my appliances. I am having a new kitchen installed and everyone is telling me that now days the washing machine/dishwasher/drier are all connected to the sink waste via the tapered spigots and jubilee clips. I had always seen this as a bit of a bodge job but...

Just to close this out if anyone ever has the same issue. I Went for 2 varilight v Pro modules and swapped them with 2 of the 3 modules in my triple dimmer. Worked a treat. Thanks for all the advise and SFK for co firming the modules were up to it. I now have a full on light show in my...

Sorry gas supply not Ha. I have a gas supply into the kitchen but capped off not being used currently as everything is electric. Do Co sensors detect gas leak? If not then is there any point in having the co sensor in there

Do you need CO in the kitchen if there is a Ha supply in there?

Thanks everyone. SFK - it is the varilight v Pro dimmer module that I linked above. Doing some research they reckon they can handle 30 lights. I am going to pock one up and swap with the current module in my switch and see how good they are. Fittings and lamps are the same manufacturer...

If i replaced the module for the kitchen and living area switch in the existing faceplate to one of <these> would that work?

I had always thought that the max amount of lamps on a lighting circuit was determined by the total wattage of the lamps not exceeding the max load of the switch. I am on the last room of the house which i had planned to have controlled by 2nr triple dimmer switches in the following set up...

So I am ashamed to admit this but it turns out the 1/4 collet was included in the accessories bag all along . Dumb ass

I have a wagner 250m airless sprayer which has saved me so much time misting the house and doing the ceilings. I now have 15 doors to paint and am not looking forward to it with a roller and brush. Is there a sub £200 sprayer that can be used with oil based paints. I assume my current unit...