Search results

By main switch I am assuming you mean a main circuit breaker because pure mains switches have no tripping mechanism. Can you post a pic of it ?. I would say the element has failed then and gone short circuit as opposed to open circuit or fault to earth with those symptoms. Have you tested...

To check the mechanical part of the switch I have had to on occasion take the whole switch section out with the power off and then check continuity through the micro switch. Then put the interlock onto the loop on the chassis while watching the mechanism and testing again. The linkage should...

Looking at them they might be after market parts ie parts supplied and fitted by the kitchen firm as opposed to Bosch. Bosch ID plates are usually etched onto the door edge or around the door area on the chassis

Those parts are usually found in the top front of Hoover fridge/freezers (behind the trim above the door) If it is a frost free the first thing we recommend is always do a full defrost for min 24 hours with the door open. Then try again Note, frost frees do freeze up

I have found it quite common for motors to go low resisitance and cause the RCD to trip when they get damp (often due to condensation after a leak or bad siting). Normally I let them dry in a warm room for 24 hours and they are ok.

Post the model number as it will make it easier to help you

Does your control panel resemble one of these on the fault code PDF http://www.smeg-service.co.uk/support/index.php?a=3&id=34

I always put a clip of some sort (spring clip or jubilee clip) on waste hoses connected to the drain via spigots. Some manufacturers provide the relevant clips (notably Bosch Group) There is nothing wrong with it at all and adds to a bit of security for it (harder to accidently get knocked...

Not the right forum plumbing would probably have been better. Have you tried bleeding each radiator to get rid of the air.

The steam should be coming from the steam vent at the rear, it depends on what you are cooking, how you are cooking it and how damp it has got inside as to how much comes out.

Does it have a series of lights along the top. The 10001 etc refers to which lights are on and which are off.

Very common, I assume you mean like this. http://www.diynot.com/forums/viewtopic.php?t=198410&start=0&postdays=0&postorder=asc&highlight=

For earth faults on these I generally look at Motor 'Brushes and windings especially if allowed to get a bit damp' Heater Mains suppressor Wiring loom and on the odd occasion moulded plug. Have you tried running it or doing a insulation resistance test with the motor, heater, pump etc...

Dont know if this helps but its the only tech info I have on any Beko kit at the moment. Beko washing machines (1715 etc..) H1 : NTC OPEN CIRCUIT OR SHORT CIRCUIT ( 10000 ) H2 : HEATER OPEN CIRCUIT ( 01000 ) H3 : HEATER ALWAYS ON ( 11000 ) H4 : VALVE TRIAC SHORT CIRCUIT ( 00100 )...

Ensure the spade connectors are crimped on correctly and tight, also the male and female ends make a very good electrical contact and are not a little loose. Either of these will cause a high resistance joint which will get hot and over time cause that.

the oven should have either an isolator (big red switch) or depending on type either a 13 Amp fused connection unit or a 13 A plug

Take the interlock out and look at it, its hard to explain how it all works as each one is slightly different, ensure the machine is unplugged first. You have a claw type part that engages on the loop in the chassis, this is connected to a piece that presses on the micro switch when the door...

Its always helpful if you post what type of appliance you are requesting help with as it saves us guessing. What fuse have you checked as some of these are plug in types plugged into sockets behind the oven. Have you got a supply into the oven at all (measured at the intake) You could...

Advisable to fit a blanking cap or plug onto the end after removing the hose as well.

If the start/cancel switch was stuck in I would expect maybe it to start then cancel constantly, not start complete program and start again.