Search results

Hi all, I'm looking to eventually replace all my household bulbs with LED bulbs, several reasons, energy efficiency being the main one, but better life expectancy secondary to that, I plan to start in the kitchen, where I have a bar with 4 halogen spot lights, these tend to be switched at...

Thanks :D

do you need planning permission or building control sign off for this kind of job?

Hi, I am contemplating removing the wall between the small bathroom and small toilet to increase the size of the bathroom, my neighbor has done it already( already done when he bought the house) and makes a big difference, the rafters run in the same direction as the wall although the rafters...

Thanks for your prompt reply. I assume replace is the only option? another development, since my original post, this is chattering on fill and drain, I'm beginning to think its a write off but will price some parts.

Hi, Ive just installed the above dishwasher, it is second hand and has been stood unused for quite some considerable time, the dishwasher fills, and heats the water, but does not much from this point, it sits silently for approx 10 minutes, then it drains and refills, occasionally it will...

As above, I've just installed a dishwasher, I've had to run the drain hose inside the cupboards to the spigot under the sink, the drain hose extension is about a meter too long so needs cutting down, I can buy the rubber boot for the end of the hose from B&Q, it has a screw thread that screws...

o.k so Ive routed the drain hose to the sink and it is about a meter too long, I want to cut down the drain hose, and put a new rubber end on the hose like this now simple enough to screw in but I suspect not water tight would a jubilee clip work or would I need some plastic solvent adhesive?

Hi and sorry for the noob question, I will be replacing the sink strainer in my kitchen sink tomorrow and the screw head is 10ml slotted, I do not own and can not find a 10ml slotted screwdriver, best I can come up with is a 6ml that fits in the hole in the screw and gives me traction to do and...

Hi picasso. luckily the spigot is on the half bowl rather than the main bowl, so there will be very little risk of the bottom of the dish washer getting filled up. Dan09 The cable you can see is part of the pop up waste not anything electric, I did dismantle the plumbing under there last...

Hi seco, thanks for your input, do you have any idea what my alternative would be?

Hi, Because the washer drain connector vents to air through the half bowl sink plughole, my understanding is because it is vented and not airtight it could not siphon back or am I misunderstanding something? Carl

Thanks for your response Breesey, what are my other options regarding running the drain hose, cupboards in situe makes it the only feasible option that I can see, also is drilling the only option, is that what was done on older waste systems. thanks

Hi, I have rearranged the layout in the kitchen, to make space for a slimline dishwasher, I have done this by removing a wine rack and shoving the fridge and freezer about 200ml leaving me a 480ml gap. I want to make this as simple as possible, so my plan is to purchase a 2.5m cold water...

hence my reason for wanting to varnish it, I just want a matt finish hence asking for advice :?

Hi I have just purchased a Mexican corona pine coffee table to sit my tropical aquarium on. obviously water and wood don't mix, so would really like to protect the table against splashes etc, the table is just waxed and is matt and I want to keep the matt look I'm thinking varnish is best as...

Hi I have just purchased a Mexican corona pine coffee table to sit my tropical aquarium on. obviously water and wood don't mix, so would really like to protect the table against splashes etc, the table is just waxed and is matt and I want to keep the matt look I'm thinking varnish is best as...

Hi taavisepp, Having done a bit more research, whirlpool state F13 is a Dispenser Circuit Error F/13 Dispenser Circuit Error If the dispenser motor is not able to be driven to it’s proper position. Potential Causes • Check mechanical linkage from dispenser motor to the top of the...

Hi taavisepp, f13 fault code could relate to door interlock are you having any issues opening the door? if it requires changing you could get it here...

Hi YanniT1980 your errors as follows: E82: Error in reading the RESET/OFF position of the programme selector EF5: Load too unbalanced; skipping of spin phases Taken From Here this gives you some simple tests to do, with a solution too lots of useful info...