Search results

So confirm this. Is that item on the wall for heating only & has nothing to do with hot water ?

Thermostat in photo is just advising the type fitted. That photo was what she sent me last year & im using it to advise people what is fitted. Either way that doesn’t answer why no hit water as I’m sure it’s only for heating. Engineer wasn’t sure how the boiler worked & don’t think he looked...

Morning. A while ago say 2 years my sister said she had no heating, decent batteries were fitted as per advice in this group & all been working since so many thanks. Long story short she lives in an apartment where the person above had a pipe split & water came through her ceiling etc etc. This...

E10 is 95 RON which is what I use in my car & other petrol tools. I’ve been using it in my tools for a while now & even this MS170 I think I will get it warmed up & then turn that single screw once more a bit at a time now it’s much warmer. Never simple is it.

Just for the record & to save people making a comment suggestion i have replaced the following for its service / possible fix for when it was boggin down. CARB SPARK PLUG AIR FILTER FUEL FILTER IN TANK FUEL PIPE IN TANK TO CARBFRESH TANK OF OIL / FUEL MIX

So i think the issue is back or just didnt go away. Same process to start as mention of which i was told is correct. Using the saw for say 10 minutes & it seems like i need to keep blipping the throttle lever or i think it will stop. When it does stop i have the lever on the running mark but im...

Yesterday i started it & left it to run a few minutes to warm up. I started to turn the screw a 1/4 of a turn & gave it a rev, i did this until i was able to rev without it bogging. Even though these are a very good copy of the original something internal must be different slightly as i was...

So the question I haven’t asked yet is When I try to rev & it bogs down does that mean it’s not getting enough fuel ie I need to turn the idle screw out to make it richer. Would that be correct.

Yes it’s a slotted screw. So tomorrow I will get it warm then try in & out until I can rev it with the bogging & chains spinning in bar. Thanks.

The screw on the carb is left hand thread. I think you are talking about a normal screw I am correct or wrong ?

Ive now got it started after a fashion but after i let it warm a little then try & give it a rev it bogs. I have tried the following but still the same. Tried it with air filter off. Tried it with fuel filter off. Tried new plug. Let it warm up longer. Spark arrester is clean & not blocked /...

New coil & Carb here & now fitted. Same start up procedure as mentioned before. Now with this new carb which is a very good chinese copy & cant get it to run. It starts & as soon as i use the trigger it stalls. Do i turn screw in or out for it to keep running. Bearing in mind i have no idea to...

All done. The new item had LOAD & SUPPLY on it. Now wired in & working fine. Thanks

Had to order the switch for tomorrow as no stock.

Ok thanks. Off out now to pick one up. I will advise once back.

ok obviously i only need it to come on when switched on. I ask as i see no info on old switch which is IN / OUT like the new one

So looking at the terminals on the item you advise does that look ok for me. I have 2 Red 2 Black 1 Earth These go into N & L & earth in its place. Looking at the one you advise i see IN & OUT so as long as i fit N & L in correct holes the only thing that could be wrong with regards In / OUT...

If i go buy the screwfix 43131 i should be able to wire it up with what i have for it to do the same job ?

I have that screwfix 43131 on my list but couldnt see the rear of it

Its just for a light. Its 20A The light switch is outside the toilet. People use the toilet & walk away. As its gets dark the neon then basically tells somebody that the toilet light is on, thats all Its on /off like a normal light switch BUT the neon is there just for visual to remind light...