Search results

instructions on my vent - eiQVENTKIT150COWL - Say that a 162mm minimum hole size is required for the kitchen vent. I already have a trusty Titan TTB631SDS which has a safety clutch, but I am told that it shouldn't 'really' be used for doing core drilling, and that 162mm is quite a large size...

ah i see what you mean it looks as though you would be right there. But do you think if I try the method mentioned above to get the post straight and then added on a baton to either end of the fence. That might (for the short-term) solve it? but again the guy did mention it took him weeks to get...

As you can see, over time the concrete slab at the bottom has sort of dropped on the left hand side and you can see a gap at the bottom. I have tried to get the fence to be fully horizontally level in order to show what it should look like when it is straight. And then the concrete post on the...

yeah I was thinking this but i guess just annoying that my friend already had the 117 and Im just having to get a brand new one to make a 10mm bigger hole lol

So the cooker hood that I have has a 147mm hole where the extraction part is The reducer that came with the cooker hood reduces it to pretty much exactly 120mm My friend who has lent me their Erbauer core drill kit which has a 117mm at the largest size -...

So i've spent a while trying to figure out the best location of where to start my tiles so that i don't end up with tons of cuts here n there because I know that if I just start from 1 side with a full tile and then just work my way across I will only need to cut 1 side of tiles, but because I...

Ahhhhhhh, thank you for this suggestion. Never thought about this to be honest, especially regarding the metal top bracket to act as a brace and like you said if any equipment needs to come in. But tbh the whole of the back has been redone already so I'm 'hoping' there's never a need for a...

Thank you for that info, it's helped me think about just having 1 opening gate and I guess I could alter the size of the moving one to whatever dimensions I wish so it's not exactly 50/50, just so I have a wider moving gate.

This is the side of my house. Having abit of work done with resin at the moment. After it's been poured and it has set id need to make a side-gate. The only support that I have on the right side would basically be the concrete fence posts me and my neighbour share. Which isn't a problem but...

Long story but we have had to change our sink (in a previous post) because our quartz worktop guy suggested that the one we had was too big so we have now opted to looking at an Inset stainless steel sink but we are trying to just work out our sizing because it seems we can't seem to fit a...

ahhhhhh thank you, yeah I was thinking it was abit of a faff to have to route it nevermind all the dust thats going to come out and having to faff around IF I had'nt gone deep enough and have to have another go around, cutting it straight off would eliminate that. yes that is the only...

Just thought I would get some further advice before I carry on but I am at the stage of getting the worktop fitted (professionally), but I am just getting all my base units fixed in ready for templating. The worktop itself is 30mm thick granite, but this area of my sink is 40mm : and this is...

Hi guys just an update, used a combined method of pretty much all your comments and have finally managed to get it off, used an old knife to protect the pipe whilst I was multi-tooling towards it. The two on the right had like 50% of a portion cut out already so those two were not too bad. it...

Basically replacing the entire kitchen units and worktop. Have already ripped out the worktop but had to cut around this previously just to get it out. So now we are left in the dilemma as to how we are going to get this remaining piece out? Obviously we want to do it without damage to any of...

we agreed on the price of the work that needed doing, which obviously included the much needed wiring for the extractor fan. he said it was an oversight on his end. ok cool, i asked to ensure that it is done and even though it would take longer now for that part of the kitchen its all good, all...

Not me lol will either be the sparky that i find or will just post up the job locally on trade/fb website. I have an sds which will be able to do the job but just dont have the core drilling bit, but even if i did i dont think i'd attempt it anyways as it seems very laborous to get through at...

ahhhhhhhh ok gotcha, i did think that the top route might have been the easiest but once it reaches past the cupboards there is going to be quite a distance till it reaches the hood which i think might be around 20cm as the hood itself is 90cm but the vent part is obviously alot slimmer than the...

unfortunately brick wall leading to exterior

its a Chimney style extractor. its this one : https://www.samsung.com/uk/cooking-appliances/hoods/wall-mount-hood-nk36m5070cs-ur/ thanks

ahh good point, i guess i can try find the route easier if i tap the plasterboard and should be able to tell where the hollow spots are and do as suggested. and no doesnt matter if the PB has holes in it as it will be tiled over. seems to also be mixed feedback regarding the issue of tiling...