Search results

Hi, it is a new set up , the chrome pipe was new but the flexi and service valve i had previously. I am going to replace because the service valve is to close to the bottom were the edge of the bath sits as i cannot get to the nuts to tighten which was my own doing , and i also have some spare...

Hi, i have a flexi pipe (15mm compresion) going to a chrome pipe for a shower , then a sevice valve not chrome going to the chrome pipe then shower , i am getting a leak from the flexi to the chrome . I have nipped it up as far as i can without striping the flats on the nut and i still get a...

Thanks for the reply, its actualy 15mill all togethere 7mill bottom 7mill side.

Hi, i have a 6 panel colinial door and i need to take 7 mill from door side and bottom , i have a electric plane . Would i be better sawing the access or using the plane . Thanks

I am putting plastic decor panels on to wooden batons and have been advised to buy MS -polymer adhesive , i am going to srewfix tommorow could any one advise which adhesives are MS polymer . thanks

Hi, i am putting decor panels in my bathroom and i have corner edging and ending strips, the problem is the room is not square and it runs out about a inch and half. the panels are 10mm and i am putting 10mm batons on the wall , could anyone recomend what i can finish the top with. The cieling...

i got it drained i used a hose pipe and attached to the pipe and run it off

In the picture were you see the white cap that is were the old air vent came off . I will try to get a pic from underneath .

I think a might have to call a plumber, every time i try to remove the connecter it still comes out pretty quick , their is no more water coming out of the taps .

I will try to upload a pick

Yes , we have a back boiler for central heating , and we also have a electric imersion heater. I have managed to completely change a toilet and bath with no problem , i am panicking a bit now , dont want to take the spedfit connecter of in case i get drowned again .

Hi , i am replacing a automatic airvent , i cut the pipe and the hot water pupmed out i managed to get the speedfit end cap on , now when i am running the hot tap to try to drain it is just trickling out , it will only come out from one tap and it is very slow . Prior to this i turned water of...

Not bought the board yet , that is if you mean the backing board , the panel is plastic cladding .

Hi, i have my bathroom ready and prepared to put some decor panels up. I am fixing them with battons which are 10mm and the panels are 10mm , i am looking for a way in fixing the shower through the panels were when i tighten the srews i dont spuash the panel . I am thinking of putting a 10mm...

Thanks for that, all done , i have also just prepared the walls i am going to put the decor panels on , any tips on putting the panels on . I will be putting battons up and using adhesive Thanks

Sorted found brackets in the instructions in a little bag. As for waste got that sorted as well, if some one could please tell me in what order i should finish fitting the bath , ie brackets to wall fill bath with water , grip fill to wall ,sealent (the one on a roll) . I will be fitting decor...

Hi, i have fitted my new bath and I have a couple of problems. The first being the waste which may be the wrong set up . The old waste says 30x20mm and the outside diameter of the grey pipe that leads out to the waste is 35mmm. When i went to my local hardware shop he said i need a reducer...

Hi, i have just prepared my bathroom in order to replace a cast iron bath , which took me nearly two hours to break up and remove and i never realised how heavy it was . I turned my water of at two points , the main stop tap in my kitchen and one in the imersion heater cupboard that feeds to a...

I was going to that , but the shower feed needs to come up through the bath to meet the shower. I suppose i could drill a 15mm hole in the end of the bath to accomodate .

I have deliberatley bought a bath that is aprox 50mm shorter than the exsisting on 1600mm . I will have a gap at one of the ends and i am not sure which one , it all depends on wethere i replace with tiles or decor panel, and the shower pipe feed. Could anyone tell me what size you can get the...