Search results

  1. B

    smeg oven door has came off and can not get it back on

    :( please can anyone help, i have a smeg sc381x, and my good wife has taken off the oven door and we can not get it back on, the hinges go into the hole in the oven but the door seems to be too big. can you give me some info how to get it back on, :cry:
  2. B

    icos system he24

    SOUNDS LIKE YOU HAVE SHARIES IN IDEAL!!!!!
  3. B

    icos system he24

    Cheers Dave, As you have said to me before ideal are costly for parts, this ideal had more than on fault on it, the PCB and then the electrode. It good that we all can talk over the net and give each other a helping hand; I owe you all a pint. :wink: Regards Tony
  4. B

    icos system he24

    Big thanks to you all, I have sorted last night; I replaced the flame electrode and set all to the correct gaps (ECT) and its running fine, But that day phoned ideal and they where struggling over the phone, but it work and a give thanks for letting me pick your brains, Regards tony :wink:
  5. B

    icos system he24

    thanks tony , i am going around there at 5.00pm, phoned ideal today the girl did not have a clue. but i'll let you know the score after i get to the customers house, regards tony :wink:
  6. B

    icos system he24

    hi tony, (long time) it dose not get that far (when i left the customer house, pump+fan and 'c' on the display with the burner led flashing all the time) the fault reset after powering down. regards tony.
  7. B

    icos system he24

    Thanks for the replay, the trap is clear and all clean after I servicing it. As the customer had not had it serviced for some time, the only thing is I was getting continuity through the lead to the electrode, but sometimes not getting a reading through on the electrode on the burner side. I...
  8. B

    icos system he24

    I know it’s been some time since I been on, but every time I come on the forum it’s always for an ideal. I have just replaced a PCB on an icos system he24 it sorted the fault but the boiler pops as if ‘gases build up’ and then decided not to work a (fault come up F L). I reset it and tried to...
  9. B

    ideal isar 30he (i have dhw but no heating)

    dave, i hope it is not the pcb, i am out of pocket already. :? worked all day for £40 regards tony
  10. B

    ideal isar 30he (i have dhw but no heating)

    hello dave, i have had a bit of a bad day, i phoned ideal about this combi and the girl that i spoke to says it was the thomisters,i changed them and h-9 fault come up so i went back, so i went back to the part center and got a over heat thomister, the boiler went through one cycle and display...
  11. B

    ideal isar 30he (i have dhw but no heating)

    thanks dave, i'll give it a good look at and i'll let you know the outcome. thanks again, regards tony
  12. B

    ideal isar 30he (i have dhw but no heating)

    hello, dave i have turned it off at the fuse spur for about 20sic turned it back on pressed the reset. just done the same dhw no heating. any other ideas, scratching my head at the minute. thank for your time.
  13. B

    ideal isar 30he (i have dhw but no heating)

    hello, i have a problem with this isar, it all works on dhw but heating side pump runs,but fan will not kick in on the display figure 5 shows. the fault diagram dose not show me the way to solve the fault, i would be greatfull if someone could give me some direction on the problem. :oops:
  14. B

    is it the pump or the divertervalve(potterton suprima 30L)

    HOPE YOU CAN HELP SUPRIMA 30L, I HAVE POWER TO THE APPLIANCE BUT DOSE NOT RUNS THROUGH THE FIRING SEQUENCE. HAS ANY BODY GOT ANY IDEAS, THINK IT MAYBE DIVERTERVALVE OR THE PUMP? ____________________________ Lynda, moderator, please read forum rule 6
Back
Top