Search results

  1. O

    Combi Boiler External Expansion Vessel

    thanks again job for monday
  2. O

    Combi Boiler External Expansion Vessel

    PS vessel isn't leaking
  3. O

    Combi Boiler External Expansion Vessel

    Thanks for reply gas112 I have found out that spec of original worcester vessel is 10 litre online i can find 8 and 12 litre vessels would 8 be ok ? system only has 5 rads and a shower room
  4. O

    Combi Boiler External Expansion Vessel

    Hi, Advice needed please. I have Worcester 24cdi boiler in my flat. Recently had an issue and it has been diagnosed as a faulty vessel. I have been advised due to the age and construction of the boiler that replacing existing vessel will be expensive and long winded. I have seen online...
  5. O

    TNS supply Ze at 1.7ohm

    He is asking same questions elsewhere
  6. O

    TNS supply Ze at 1.7ohm

    I would describe as a wrap around P clip with a pinch bolt. I think it is copper or maybe brass? I’ll ask my electrician if he knows. However my first question remains Is Ze of 1.7ohm ok?
  7. O

    TNS supply Ze at 1.7ohm

    So much higher could it be to be acceptable? Before the CU was changed, the flat has been owned by my wife’s mum, and now us since 1994 Never had a fuse blow. Never even changed a light bulb for mum
  8. O

    TNS supply Ze at 1.7ohm

    Can someone explain please?
  9. O

    TNS supply Ze at 1.7ohm

    Yes out of solid floor Not sure it’s mounted in box 415v Haven’t taken any since Said it is high Irrelevant it was test direct to the clamp that is seen
  10. O

    TNS supply Ze at 1.7ohm

    try again
  11. O

    TNS supply Ze at 1.7ohm

    Pics before board chan
  12. O

    TNS supply Ze at 1.7ohm

    Pics before board change
  13. O

    TNS supply Ze at 1.7ohm

    I’ve got a couple of pics before CU swap I’ll dig them out. Electrician hasn’t given me paperwork yet, I told him I’d like to get the bottom of problem now and then do retest
  14. O

    TNS supply Ze at 1.7ohm

    Thanks for reply We’ve tried cleaning a polishing cable of clamp. The reading was taken direct onto sheath of cable. If they say go TT who tells the other 2 flats?
  15. O

    TNS supply Ze at 1.7ohm

    Hi just had a consumer unit changed in a ground floor flat that i own in Newport Gwent Flat is fed via a cable that pos out of the floor and terminated in a 415v steel box. One phase is then split out and feeds my local meter and CU. The remaining cables are then fed up to the ceiling, where...
  16. O

    Retro fitting LED lights

    Can’t drill new hole as the led module is mounted centrally on the lamp base Rotating the base doesn’t help alignment as the base needs to be central over the conduit box otherwise the appearance would look cowboyish if the fitting isn’t in the centre of the Artex circular pattern. Not fussy on...
  17. O

    Retro fitting LED lights

    Good Morning Advice please I’m removing a couple of old glass/metal light fittings ( no earth connections) They are mounted on existing 2BA screws centrally over a round steel conduit box (BESA?) The flex is in to fitting is just off centre, but pos through and terminates ok. I want to fit a...
  18. O

    Earth connections in steel conduit lighting corcuit

    So I have found out since I started looking. When I was a boy I couldn’t find metric screws……
  19. O

    Earth connections in steel conduit lighting corcuit

    Yes I did and discounted the idea very quickly
  20. O

    Earth connections in steel conduit lighting corcuit

    Finally got around to dropping a light fitting The light was removed to reveal a round conduit box No earth connection visible inside The light fitting was attached to the box using the tapped holes. I think the screws are brass 2BA ? I rigged up a fly lead attached to the conduit, ran it back...
Back
Top