Search results

seems ok .pump rocking and rolling but no boom from boiler..am hoping new board in boiler will cure hassles :?: :?: :?: steve p.s am thinking of giving up telephones and changing to plumbing and heating as real decent problems to get teeth into l.o.l

super well another day done .next time you travel up the coast to norfolk poke your head in and i'll treat you to ice cream or a nice shandy..thanks again for your time and patience very much appreciated. best wishes steve. p.s will keep you informed how things pan out :D...

yes pushed button turns over but no boom..will get my heating enginnr to look at this as nearly pay day. out of interest should i have voltage to room thermostat cheers person who doesn't sleep.. :D Steve

the moment of truth..put h/w on ...pump all ok.power to boiler...no fire in boiler...spoke to my local heating engineer the other day he reckons circuit board may be on way out as before all probs used to go out to boiler press button and boom away she went... do you think it's a good idea to...

that might be were i put it back in wrong then...dare i turn it on now ????? with just 1 3 4 connected .....getting cold up on the coast.

no wire at present....

me thinks this is the house jack and jill built whilst high on some form of drugs.. :D colours not tallying up as most wiring as in old or new house cabling i.eblue black brown ea to tank stat etc...think i have worked out which wiring is what though.. :D now 2 central heating off...

ok now sitting in front of wiring box..h w off Grey from 3 port valve is poss 2.now moving to 1... like being in the dentist l.o.l ouch

hi seco .thank's very much for reply..same instructions as i have.only problem is on old wall block behind old programmer was connected n l 2 3 4. no connection to 1 have been looking for wiring diagram to see what is astray..i'm 99% positive i put all connectors back as was...

hi guys after a bit of advice.had probs with rusty 3 way valve and busted programmer.Drayton tempus 7.now got new stuff in place swopped old for new but a bit dubious about wiring as back of old programmer different from instructions on new...

http://www.screwfix.com/prods/37586/Plumbing/Central-Heating-Controls/Drayton-Tempus-7-Programmer 304036 DRAYTON TEMPUS 7 PROGRAMMER 90.48 104.06 around 50 pounds sterling for 600 yds i know where i'm off too cheere seco thanks for your time and advice much...

yes just read through the instructions and looks like its hot water and heating on or off...no either h/w heat now understand :D :D :D thanks again seco i'm learning slowly steve

my local plumb centre this p.m electrician after wireless room stat. salesboy...all the boxes look the same do you want to come round this side and see what your after....l.o.l and the electrician did. so long and short...if i get a replacment drayton newer version 7 off with...

looks like a trip to plumb centre again....thought all timers the same not.... is there a big difference between single channel and my old drayton 7...plumb centre doing new drayton 7 so will pop in there and get replacement. :cry: :cry: :cry: phone lines are easier to look...

yes definately single channel :D thanks steve

wiring conversions instructions tried to simplify mains load ea n l com off spare on ea n l 1 2 3 4 for conversion from drayton tempus 1 and 2 ea n l...

evening serco hope you had a good day.....poets day yahoo :D danoss randall ts715 si instruction book says could swop for my old broken drayton tempus one and two..i have a seven but am hoping 1 2 7 wiring all the same. steve

danfloss that's the future....out with the worn out drayton tempus 7. got myself a ts715 si turbo...and looked at wiring diagrams for the last 3 hours....there different...any clues as to swop the 2 much help appreciated :D :D :D :D thanks steve

morning another day.. programmer was lighting up when when heating called for,also hot water.power in but not out even when 3 way valve pushed over etc.. suspect it is deceased thanks Steve

hi removable lower half of socket is master socket.take lower half of socket off try broadband in there first and see if you can measure the speed either on router via i.p address or speed test site on web.then move hub/router to where you need it and speed test again.if big difference go...