Search results

  1. J

    Opella toilet syphon

    Not sure about if I had instructions was a while ago , is it normal to have approx 2" of water in the cistern after its been flushed? Thanks
  2. J

    Opella toilet syphon

    Hello, I fitted an opella toilet syphon a few years ago it has never given a complete flush both of the blue plugs are in place should I remove one or would that make it worse. Once flushed the water level is just below the lower of the 2 blue plugs leaving approx 2" of water. Should all of...
  3. J

    Halstead Ace High

    Hello , How difficult is it to change the diverter valve please?
  4. J

    Halstead Ace High

    Hi Ian, Yes one of the 22mm central heating pipes is hot. Is it straight forward to change the diverter valve , I assume its the diaphram that needs replacing ? Is there a " How to guide " on this forum for changing a diverter valve ? Thanks for your help Ian
  5. J

    Halstead Ace High

    Thanks Ian, I will check later tonight Thanks
  6. J

    Halstead Ace High

    Hi Ian, The burner does stay on when the hot water goes cold. Thanks
  7. J

    Halstead Ace High

    OK Ian, I will have a look Thanks
  8. J

    Halstead Ace High

    What would that mean if the flame went on and off during the HW? Thanks
  9. J

    Halstead Ace High

    Hello , I have the above boiler, just recently the shower would be hot then the water would go cold after 3-4 mins the hot water would come back on. We live in a hard water area, would a descale of the boiler help or is it a valve ? somewhere getting stuck ? Thanks
  10. J

    LG Direct Drive 9Kg

    Hello I have the above washing machine. The problem I have is the conditioner does not enter the machine , it is still in the tray when the machine has finished its cycle. The missus is getting annoyed !!
  11. J

    Halstead Ace High

    Hello Harry its a pressurized system and its at 1.5 bar do you think it needs more water in the system ?? Powering it off works but I cannot keep resetting it !!
  12. J

    Halstead Ace High

    Hello approx once a day when I turn the hot tap on or the central heating on nothing happens (no error lights). the boiler is dead quiet with just the green power light lit. I have to resolve this by powering down the boiler wait 10 mins then its ok again. Does anyone have any ideas please ...
  13. J

    Halstead Ace High

    Yes have tried the rest knob but does not always work, so I power it down for a minute then switch on Thanks
  14. J

    Halstead Ace High

    £3.50 for a thermistor and £54.00 for a new motherboard with 1 year guarantee. It turns out I did not need a new motherboard , but since I swapped the motherboard I get the Lockout problem which is cleared by turning off and on the electrical power to the boiler. Suppose I should put the old...
  15. J

    Halstead Ace High

    I recently replaced a thermistor as it was shorted out and replaced the mother board , since then the boiler often goes into Lockout when switching on the heating and or hot water. What does it mean when it goes into Lockout please? And how do I resolve this? Thanks and a Happy New Year to...
  16. J

    Hotmail Account

    OK did not realise that Thanks Again
  17. J

    Hotmail Account

    Hello, I wish to contact someone who had a Hotmail account but as Hotmail no longer exists how do I contact them ?? I do not have a phone number to ask ! Merry Xmas
  18. J

    Halstead Ace High - No heating or hot water

    Yes the measurement was across the 2 pins of the thermistor with the plug disconnected. In order to change it I have to drain the boiler but cannot see where the drain is ??
  19. J

    Halstead Ace High - No heating or hot water

    Could someone kindly point me to a link to " How to drain a halstead ace high boiler " please ?
  20. J

    Halstead Ace High - No heating or hot water

    Should both thermistors read the same ie approx 15 ohms as one reads 0.00 ie a short
Back
Top