Search results

  1. A

    Beko WME7267W changing waste pipe

    got it now, thanks rocks.......... didnt read your reply properly, apologies!
  2. A

    Beko WME7267W changing waste pipe

    so i need to take the back off the washing machine to get it out? Doesnt it just 'push and turn'? if i need to get the back off then no problems, seems a lot of work involved to 'change it over'. If its whats needed then off it comes thanks andy
  3. A

    Beko WME7267W changing waste pipe

    thanks rocks The waste goes into the back of the machine at the top on the left. Looks like it needs to 'turn' to unlock, do i need to take the back off the washing machine to get acess to it? andy
  4. A

    Beko WME7267W changing waste pipe

    Hi all Ive got the above washing machine, the problem i have is that mice have bitten through the waste pipe causing the water to go over the floor and not to the drain. Ive managed to get a replacement hose, just needed to know how to change them over? Is it a case of pushing it in and...
  5. A

    new heating controls

    Hi all Just after some advice. Ive currently got a honeywell ST799 programmer and a honeywell DT200 room stat and wanted to change it to a wireless system. Would the honeywell cm927 be the way to go? Basically ive got a couple of rooms in the house that get very cold and the room where...
  6. A

    danfoss room stat - wiring problem?

    Thanks picasso will give that a go. I understand it difficult trying to diagnose in the forum, hopefully just a mistake with the wiring cheers andy
  7. A

    danfoss room stat - wiring problem?

    Thanks Picasso I did the same with the cylinder stat that i did with the room stat; turned it up and down so the stat clicked to turn the boiler on and off as per normal. If either or both stats were incorreclty wired would they then blow the fused spur, rcd and programmer if they both...
  8. A

    danfoss room stat - wiring problem?

    Thanks Picasso So by checking and ammending the wiring should sort this out? Why though would it run for a while and then blow? I had been testing the room stat by moving the dial to click on and off which would turn the boiler on and off thanks andy
  9. A

    danfoss room stat - wiring problem?

    Thanks Matt Im pretty sure that the £ port valve is wired correctly as it works when either the heating or hot water is selected, or both. I think it could be to do with the room stat as this works in reverse; ie 10degrees setting is 30 degrees, and 30 degrees setting is 10 degrees. I...
  10. A

    danfoss room stat - wiring problem?

    Just spoke to the customer and the fused spur has gone, the rcd has tripped and the programmer is dead. I think maybe there is a bit more to it than the room stat
  11. A

    danfoss room stat - wiring problem?

    Its a danfoss RMT230 room stat. This was the only thing that wasnt right. I had to fit a new 3 port valve which operates ok, a pump and a cylinder stat.
  12. A

    danfoss room stat - wiring problem?

    Hi all Fitted a danfoss room stat yesterday as a replacement for a honeywell room stat the was faulty. When i turned the room stat up to call for heat, boiler fired and ran normally. Got a call today that the fuse has blown after the boiler had been running for around 2 hours or so. The...
  13. A

    Oil spares in the van

    Thanks Terry that gives me something to work on cheers andy
  14. A

    Oil spares in the van

    Thanks Terry I can sympathise with where your coming from as i too have had a customer or two say the same or when im on my way to the merchant google the part and then say it cost this much when the jobs done. I now dont tell them too much just i need to get some spares from the merchant...
  15. A

    camray compact - quick question

    im assuming theres a problematic one in Langham! :wink: Got a year before i go back and fine tune my technique. your certantly right, it wasnt nice to work on, and the customer thought he had a bit of knowledge as well and watched me like a hawk! Not what you need when you cant get the...
  16. A

    Oil spares in the van

    Thanks everyone Will look into getting the extra bits when i can. I wanted to get to a stage that when im get a call at night for a breakdown, i had sufficient in the van to get me out of trouble Boilerman - Im on the suffolk/essex border, dedham area, you? cheers andy
  17. A

    camray compact - quick question

    Hi all Went to service a Camray Compact boiler yesterday, first time ive serviced this particular model. Any easy way to get the burner out to service it? I tried turning it numerous ways still couldnt get it out. In the end i removed the burner from the blast tube to be able to change the...
  18. A

    Oil spares in the van

    Hi all Ive been out and about for the last 6 months doing oil boiler servicing and breakdowns. Ive got a few items in the back of the van which will hopefully get me out of trouble, just wondering what would be considered a minimum stock to hold in the van? Ive not got thousands to spend...
  19. A

    Wallstar Oil Boiler

    djsarge thanks very much for the advice. The clear flexiline doesnt seem to twist in the fingers, when i was there last time i had no air going through the flexline, just the standard bubble. Will certantly go to the danfoss website and try to download the booklet. Once again, thanks for...
  20. A

    Wallstar Oil Boiler

    thanks Stumpy I have one of those in the back of the van, though the pump thats on the burner is a delta pump. Do i need to change the pump to an danfoss pump for the coil or can the coil go on the delta pump? cheers andy
Back
Top