Search results

Thanks Chris that was another issue not having enough room to adjust the drop

I need to run it under the floor to get where we would like the pan, but 2 90° take it just above the joist which is why I wondered it I could use a 45 into a 90

Hi there We are thinking about changing layout of ensuite but have a question about soil pipe, the current soil pipe is in a box section under joists and position we would like toilet is about 2m away but I need to take soil 90° and up in between joist, I was thinking about joining 2 90°...

I am re-modeling our en suite and need to remove the 20mm chipboard because it's not level and I need to add longer soil pipe, so if the final finish is going to be 10-13 mm slate tiles on top of 4mm underfloor heating mat, what thickness ply would you use? Many thanks Brett

Hi there we have developed an airlock in the hot water, about 3 months after i fitted a pump to boost the hot pressure. it started when my son was trying to adjust the temp on the shower/bath thermostatic taps and now if you open them up over half way the air lock starts to bang. all of the...

I can't believe i didn't think of this! this is exactly what is happening many thanks Brett

Depends on what?

Hi There I am still trying to sort out this pump issue, I have a cold water tank in the attic which gives fantastic water pressure all around the house, and I have a hot water tank on the landing with bad pressure around the house. I have been told a single pump for the hot water will be ok...

The hot water in our house is terrible so have decided to get a pump for the hot water (stuart turner universal monsoon) the question I have is how long should such a pump take to install, the tank is heated by solar or gas, it also has an electric emersion heater but this has never been used...

I have a small rear lobby area about 1m x 2m, it's basically where we hang our coats and the dogs sleep at night, I have some spare amtico boards and wondered if i could stick them down with a 50mm wide tape? the only thing i thought might be a problem is would water get in the joints when i...

Afternoon all we have been planning to replace our patio and run a new strip of 600x600 along the fence to put flower pots on, not for a pathway. But when i replaced the fence I found an inspection cover buried about 150mm so my first problem is that its not the same level as the one in the...

It's in our main bathroom, I have used a 2 way thermostatic tap for shower/bath so am now wondering if that might be the problem as it was OK with old bath and taps. Can you adjust the flow on these thermostatic taps

I know this has been covered before, but I cant see anything about the same sort of system I have or an answer I have a coldwater tank in the loft a open vented hot water tank on the landing solar panels for the water worcester condensing boiler cold water flow is fantastic...

thanks guys, it does indeed look like its a CH pipe that is causing this, it hadn't crossed my mind but as i think back it has only been noticeable since the central heating has been switched on, its not a massive problem its only my 2 boys who moan about warm squash

our mixer tap in the kitchen does this but i cant understand why, hopefully someone can explain we do washing up so have run hot water, then when i rinse with cold after about 20 seconds the water goes hot for about another 20 seconds and then back to cold this will do this even if i turn...

I haven't asked him yet, as we are quite rural I just thought I could run a straight pipe from outside wall to the area of the hob so I can carry on with rest of the kitchen and then get him to come and connect both ends

what size pipe should feed the hob? the old hob fitted has the microbore, quite flimsy/bendy pipe that comes out of the wall and then jubilee clipped to some orange pipe which fits to the regulator i have a new hob that will require a different route due to kitchen remodel and just wondered...

I have a 6kg tub of Amtico universal 2 part adhesive, but i only have a small bathroom so dont need to mix it all, my question is does the hardner only go off when mixed? and what sort of ratio should i mix the adhesive/hardner? Thanks Brett

horizontal bi fold with 2 panels so as my doors are 650 do i have to have them both at 325? or can i have 1 at 390 and the other at 260 making a total height of 650

at the moment the wall units are a standard door 600 wide and 650 high, now the plan is to convert to bifold and i just want to know if both panels would need to be 325 high or could we go something like 390/260, the panels we are looking at are 390 so this would mean cutting one rather than two