Search results

I WILL NOT relate my Wallstar experience, many others seem to have covered ALL my problems and some of the remedies. :shock: I am a retired electronic engineer and I have left the maintenance of the Wallstar to the "aledged" experts, for insurance purposes. Howevever we have been plagued by...

The saga continues :- This problem has fooled me since it seemed intermittent. :shock: We complained about the terrible stink although the rotors and water circulation while washing was quite powerful. Just found service invoices going back to 2002.!!!! the single motor was replaced by...

Hi Leccy If youn are still there. I cirtainly am, and still have this intermitant pump out. We were advised to have tthe Timer replaced, at great expence. A few days latter Wife said "It's not emptied !! Some details :- Zanussi DWS 939 Prod No. 911883002 Type 911N81-2F SNo...

Here we go again ! After weeks of working OK .. back to no pump out. Now with egg on face. Another theory bit the dust. :shock: Convinced that the problem was due to an intermittent micro switch I replaced the Timer at great expense. It worked fine, cracked it ! brownie points ! for...

The rotation noise is unbelivable ... like a steam train chuff chuff ... why is this ? If I stop it rotating .. no noise. Advice on how to silence this appreciated . Without dropping a knife down the hole :lol: Regards flounder

Just done a drain test, again, and checked the outflow of the machine. The pump out was powerful and had a head well over the height of the drain pipe. The input to the drain has a “splitter” Y connection and is fed from the washing machine one side and the dishwasher the other. There was a...

Just look at the date ! Put up with this intermitant draining problem all this time .. After the bearing and seal packed up on the pump it was replaced recently. Ihe impeler blades on the old pump were in good condition. I thought the new pump would solve the problem .. But the...

Does it start without you re-starting it ? When the boiler has switched off can you hear the circulation pump running ? A stuck pump will cause this. The heat in the boiler exchanger will linger for a long time if the energy is not removed by the pump. Say 10-15 mins A massive air lock can...

This is very frustating ! We thought all water was pumped out the other day. But when the door was opened there was a stink :oops: The water level was just under the bottom filter and was filthy ... Still think the switch is faulty Can anybody advise how to get at the switch ...

Thank you Leccy This is a single motor combined pump, circulation and on the end of the unit the drain out pump. On first swithing on there is a pump out function. A significant point is that the control knob, if turned to the Red end of cycle wedge, will mostly pump out energetically...

Dose not empty after wash cycle. If the program rotary switch is turned it can start an empty function. The motor is new as the previous one seized up due to seals leaking. Most of the comments about this kind of fault refer to the end impeller blades being damaged, but this is a brand new...

Ok, got my knee pads on and the back cover off. The motor brushes almost finished so they were replaced. Although the fused timer circuit was repaired, when power was on, the motor was dead. Now trying to find a circuit diagram. Any report of malfunctioning micro switches in the timer...

Will not spin A printed circuit track has fused, terminal 10, repairing this with fine wire still no spin. Not taken back off yet because of my knee’s :( Help appreciated. Regards flounder

Conditioner syphoning a right pain. Tiredengineer suggested the cleaning siphon routine. Look down the vertical siphon tube to the very bottom and then push a thin wire along the bottom of the tray until you can see it beneath the vertical tube. Waggle it to dislodge any algae. Also another...

Thank you again SH Will be dragging it out today I think. Will let you know of the progress. Regards flounder.

Thanks Not so Sleapyhead That is great news. I did not want to get on the proverbial conveyor belt. Will take the top off . Is there a solenoid control? Many thanks for you response Regards flounder

Sorry but this is a re post just to jog memorries. The washer is a FJ 1040 no water feed to flush out the conditioner. The tray is clean and the syphon works on testing externally. I would appreciate knowing why there is no water feed to the conditioner section. I have poked nylon line into...

Thanks JohnD It went so quiet that I thought my post was not getting out :shock: Will have to try to get a circuit diagram to find out if there is a relay, solenoid etc in the flush. Thanks JD

:shock: :( What I don't know ..... are there other readers on this forum or am I the only one reading my own postings? A simple message would confirm that, although there may not be an answere to my problem, at least it has been read :oops: :cry: Regards, flounder

This seems to be a common fault but I have not found a solution so here goes again. No water feed to flush out the conditioner. The tray is clean and the siphon works on testing externally. I would appreciate knowing why there is no water feed to the conditioner section. I have poked nylon...