Search results

yes this image is from the instructions provided.

I would like to fit an extractor fan in the loft space above my shower room with ducting to the outside. I want it to come on when the light is switched on. The type i have is without a timer overrun. The instructions say to put a double pole switched connection unit in the circuit before the...

pics

Thanks for that - I have an RCD fitted at the consumer unit - this states 30mA and covers the sockets. It's a house and the bedroom is below the loft space. I will ensure the FCU is placed before the socket in the loft. So i can run the cable in the cavity - and none of this need to be...

Can i have an additional socket installed in the room taken from a Fused connection unit in the Loft space ( I have a socket in the Loft ) I want the cable to run in the wall cavity and be behind a TV on the wall. Would this work need to be notified? Also my wall lights would need...

OK, so i can have my existing socket removed and plastered over & have the cables extended to where i want the socket to be moved to and have them plastered in the wall too. Also my CU is quite modern with an RCD unit.

I would like to have a double socket relocated across a wall space in a bedroom and have the present ceiling light removed and instead have a couple of wall lights in the same room from the existing light switch. the room has a loft space above. I would also like an additional socket added to...

Thanks for the replies here - good advice. I connected the 5 x 20W Halogen 12V to the transformer (single output from one of the transformers 3 outputs to a JB). The lights DID NOT work. I took one of the bulbs out and tried again, after about 5 seconds or so, the lights came on. I tried again...

The instructions are not very good with this transformer, but i could not find anything about safety margins stated.

I would like to install 5 x 12V Halogen lights using a DAIS DA-105 transformer. Each light is 20W. The Transformer states the MAX is 105W/VA. The instructions are not very good, so want some advice. 1. Can the transformer take this load ( 100W ) 2. The transformer has 3 outputs for lights...

Had a word with the previous owner of my property and it seems that i have not got an Immersion in the loft as i was told previously, but just a hot water cylinder with a thermostat attached. No water is heated by the electric other than my kettle. Many thanks for the posts here ... If i want...

I want constant temp really on both showers. The Hot Water comes only from the Immersion in the loft (from what i understand). This is why i wanted two Electric Showers - I really do not want to alter the plumbing system (other than feed the cold to the showers).

I was told my boiler was not a combi and would not be suitable for 2 showers.

Boiler heats the Rads, the Water is heated by the Immersion, all the plumbing is linked in somehow - it was explained by the previous owner. But only a small Hot tank (like the size used for hot water in a Canteen or such like - not very big comapred to the big copper tank i had in my old house).

I'm sure that the Main Fuse is 100A as i was told by the previous owner that all this was upgraded when the house was rewired a couple of years back, the electric supplier installed a new meter, board & Fuse. The Meter and Fuse side of things all look quite new and it states 100A on the...

Also ... am i correct in stating that Modern Electric Showers do not operate at full Power all the time whilst in use?

Thanks for the replies to my post - I have a GAS HOB and an Electric Oven, but it's one of those modern low power types that plugs into to a socket outlet with 13AMP fuse fitted. I've still got to get in the loft to find any details on the small immersion heater up there, I have a modern GAS...

Yes - Plumbing was upgraded before i moved in the property, plumbing is not a problem at my property.

Hi all. I'm looking at having TWO Electric showers fitted at my property. I've seen what i would like and they are 9600 WATT at 230 V. I have a modern 17th edition split Consumer Unit installed already, with space for a couple of MCB's on each side. My supply Fuse is 100 AMP, my Consumer unit...