Search results

  1. C

    RESOLVED Miele CVA7445 brew unit

    For anyone coming to this thread with a similar issue I’ve managed to resolve it. There appears to be no hidden menu on this model therefore I decided to dissemble the brew unit and remove the cogged part of the mechanism. Leaving this out and screwing the brew unit back together I could...
  2. C

    RESOLVED Miele CVA7445 brew unit

    Yes I’ve reset it several times There’s not much to see really, a cog that’s slightly misaligned and the corresponding cog on the brew unit won’t align to it
  3. C

    RESOLVED Miele CVA7445 brew unit

    Does anyone know how to initiliae the brew unit on the above machine please? The brew unit was removed to clean it and now the motor cog is slightly misaligned and it's now impossible to reinsert the brew unit. Instructions followed (turn machine off and wait, turn on again and motor should...
  4. C

    Videx gsm and doorbell

    Press the call button on the Videx gsm and the bell rings Press the doorbell button at the door and the bell rings
  5. C

    Videx gsm and doorbell

    Finally got round to putting sparkymarka’s advice to reality but hit a snag… The bell (as most seem to be) is ac, the Videx outputs 12v (actually closer to 14.5v) in dc There’s also a regular doorbell transformer to through in to the mix. The doorbell is rated 8v What’s the best solution...
  6. C

    Came frog and videx gsm

    Yes I get 13 volts at the +/- terminals when operating the relay.
  7. C

    Came frog and videx gsm

    Will the came control panel accept voltage at the inputs or is it specifically volt free does anyone know?
  8. C

    Came frog and videx gsm

    It’s possibly GSM4KCR It’ll work on 2g until they deprecate that network too. The relay came with the kit and has worked previously on a ‘nice’ system
  9. C

    Came frog and videx gsm

    I don’t think tha 3g version is volt free
  10. C

    Came frog and videx gsm

    Just to clarify I’ve folllowed the instructions in the videx manual regarding the art120
  11. C

    Came frog and videx gsm

    Even the 3G version?
  12. C

    Came frog and videx gsm

    Struggling a bit with this If I short 2&3 on the came controller the gates open however entering the code on the Videx nothing happens. Relay time set to 2 seconds What am I missing?
  13. C

    Stihl re129 plus pressure washer fault

    Thanks I should have mentioned I’ve cleaned this previously without any noticeable improvement
  14. C

    Stihl re129 plus pressure washer fault

    My pressure washer has a fault where it won’t start on the trigger reliably. It was repaired under warranty some time ago but I don’t know what was replaced at the time. Can anyone advise what the likely required part is please?
  15. C

    14mm to 15mm copper reducer?

    Just trying to work this out, do you mean sleeve the 14 with a piece of 16 then the other side slip the 15 over that?
  16. C

    14mm to 15mm copper reducer?

    Is there such a thing as a 15 >14mm copper reducer for French plumbing fittings?
  17. C

    Pipe thermostat for fan override

    No it’s copper. The issue is the stat is exceptionally slow to respond to the change in water temperature, by which time the humidistat on the fan has kicked in.
  18. C

    Pipe thermostat for fan override

    Thanks all I’m going to try and use a flow switch in line to the shower head as I only want the fan to boost when the shower is being used, otherwise I like a nice peaceful bath. Anything else I haven’t mentioned? Probably, but not relevant to my preferred solution!
  19. C

    Pipe thermostat for fan override

    Because I don’t want to be in the bath with a typhoon style fan running!
  20. C

    Pipe thermostat for fan override

    The pipe to the shower head. The issue is the cheap pipe stat I think
Back
Top