Thank you both for your advise, I phoned the provider again they still said the woodworm would not have caused any great damage and that it was OK to use! ( incredable how someone on the phone can see into a piece of wood to see woodworm damage ) I have asked again for a replacement which...
Hello
I have just had some tanalised wood delivered to make a gate, two of the lengths are good, the third has woodworm holes ++ I phone the provider and was told tanalised wood would have been treated for woodworm so the hole are not an issue, is this right? I do not want to make the gate...
Hello John,
I have taken a couple of super macro picture of the fragment that came out it's length is 5mm I do not think it is part of the brush what do you think?
Thank you John and Dave 54.
I have taken the jigsaw apart as I did so a tiny metal fragment fell out and a broken brush ! I have re assembled and it is now working. I will have to order some new brushes but so far all OK. As for the tiny metal fragment I could not locate its origins.
Thank you...
Thank you John for your reply.
The jigsaw has had very little use still looks like new the cable is sound, no burning smell when it stopped.
Will dismantle and check brushes and switch as you advise. Thank you
Can anyone advise as to what may be wrong with my orbital jigsaw. I was using my jigsaw today and it just stopped working, the fuses are fine. Any advise welcome.
Gas man has been :D !
Fitted new thermocouple, but could not light pilot light at all, found jet to be blocked, jet should have apparently dropped out of component but is firmly fixed, chap managed to unblock jet with needle.
All now working although pilot sounds like a jet plane, this is...
Thank you Tony, the last twice the 'gas man' came I had already taken the fire front off.
Answer to a previous enquiry I live in a cottage built in 1892 which is situated in the middle of a 66 acre field, no trees nor buildings for shelter and the winds do blowand howl, it's great but better...
Thankyou all for your replies,
the phone rings before it goes to voice mail, does this mean something?
When I do get a 'gas man' to come I will let you know the results.
I exposed what you have called the clutch housing to me it looked like the brake calipers you find in the braking system for clasic Volkswagons, that is why I discribed them as calipers, sorry for any confusion.
Boiler is a Baxi Bermuda.
Serviced last November. At which time the gas mans used a reader and said the fire and boiler reading are better than todays models.
pilot light was blowing out in very strong winds in the Spring, but always re ignited easily.
I had the chimney pot and liner...
I have a mature LPG Baxi boiler, in good order normally and serviced annually.
I am having problems with the pilot light being blown out, I think it may be due to wind coming down the chimney is this possible and if so what should I do about it?
Unfortunately my Humax TV with a speaker bar fitted below the TV has give up. I have purchased a Blaupunkt TV but the sound is tin like,
I would like to know if it would be possible to take the sound bar off the old TV for use on the new ? if so can you advise?
Alternatively I have looked...
Detached the engine from shaft, within two calipers with central spring, plenty of carbon dust no rust, cup /drum at top of shaft held to shaft with four bolts unable to remove three bolts as they do not align with either of the insert / removal holes, cup /drum not tight on calipers on...
Yes, the engine is now fine, I have WD40ed the bolt heads at the top of the shaft by the engine and hope to dismantle this weekend, will let you know what I find.
Sorry I did not get back sooner Burnerman, other 'things' have taken priority.
Stripped carb, checked all screws ect, engine now running very smoothly, sounds good, however the cutting attachment is still running in idle, any advise welcome.
Thank you for replying Burnerman. Ive checked the cable which is working fine and is in the correct position.
Ive also emptied the petrol out, replaced with fresh, checked and cleaned the air filter and cleaned the carb the engine seems to run alittle slower but the cutting attachment is...