Search results

  1. G

    Accenta G4 fault PIRs

    I have accenta G4 unit in garage, key panel in house, few contact sensors and three PIRs. Had a kitchen fault other day so alarm wouldn't arm. Quickly checking the systems indicates the contact sensors are fine. It looks to be all the PIRs which are dead as there is no red light. Checking the...
  2. G

    Valiant Ecotec 831 combi heating turns on random

    Cheers both looks like the central heating pipe starts to get warm when I run the hot water so I suspect the divert valve
  3. G

    Valiant Ecotec 831 combi heating turns on random

    Yes it's turned on. I've just turned it off to see if that improves. Do you think that could be impacting? Surely that's on the hot water circuit rather than the heating circuit?
  4. G

    Valiant Ecotec 831 combi heating turns on random

    Got the Ecotec combi 831 and lately I have started to hear the heating kick in even though temp is set to 19C and its reading 23C! Anyone come across this? Wondering if the Honeywell thermostat/programmer is faulty or could it be a faulty sensor on boiler? Recall reading boiling has a low temp...
  5. G

    Belo oven wont work SCC2632

    Hello all My mothers oven has stopped working and was wondering if any of you have some suggestions as to what could be wrong? Its a single oven Beko SCC 2632. She mentioned the grill in it still works
  6. G

    Removing Aluminium sliding door

    cmother thanks for the info Im going to have a go tomorrow and see if I can remove the sliding door and the fixed panel without breaking them! If it comes out ok Ill purchase a new frame. Thanks
  7. G

    Removing Aluminium sliding door

    This will be slightly difficult as my camera is buggered! but was wondering if someone had a general idea of how to remove my aluminium sliding doors? The reason being the sill has rotted and I need to replace it so was going to remove the sliding door and the fixed panel to make fitting a new...
  8. G

    Ford Ka heater just blowing hot help

    right then Iv found the valve and there is a constant voltage going to th valve regardless of where the heater control is positioned. I have removed the ontrol panel and measured the rsistance on the variable resistor and its low and makes no difference when i turn the control. Am I rght in...
  9. G

    Ford Ka heater just blowing hot help

    Iv got a 2004 ka sport and the heater just gives hot air all the time regardless of what position its in. Can anyone give me some advice on a fix please? Im assuming the heater control is a variable resistor of some kind and the voltage varries when the knob is turned? If I measure the voltage...
  10. G

    Worcester 24CDI thermostat help please

    mogget cheers i shall have a nose this week
  11. G

    Worcester 24CDI thermostat help please

    Gremlin cheers for that can you give me anymore detail on fitting it to this particular boiler as my father does not have the documents for the boiler? Or if you could point me in the direction of a wiring diagram that would be great. Thanks again
  12. G

    Worcester 24CDI thermostat help please

    My father has one of these boilers but there is no thermostat so it turns the house into an oven and means the boiler is not running efficently. Now it has a digital programer built in so Id like to install a thermostat. Id like a digital programer/thermostat worcester one ( anyone recommend...
  13. G

    Large tile fixing advice please?

    jefoss or anyone else do you have any recommendations? :D BAL/ Dunlop?etc
  14. G

    Large tile fixing advice please?

    Iv just ordered a large ceramic tile(Sahara Marfil) which is about 30x90cm :shock: . I have not used tiles this large before so would like some advice on how to fit them and also if anyone can suggest a good adhesive? thanks in advance :D
  15. G

    Dryline or Tanking ?

    modernmaterials Iv got to be honest you’re an idiot. :? Why have you picked up on a point which has nothing to do with the question? If he had this problem in the other properties then he would know what to do and subsequently wouldn’t need to ask advice on here. I’m sure the author is thinking...
  16. G

    Silicon around shower tray not bonding

    Recently fitted a shower tray and I have sealed all the way round with silicon for use in bathrooms but the stuff just does not want to stay bonded to the shower tray in some places!! :( Has anyone any ideas? Was thinking of spending more money on a named brand of silicon but it might just...
  17. G

    Cleaning percelain tiles. HELP

    Right then I have laid some porcelain tiles in my kitchen and they wont clean up. They are a black/dark grey tile and I used a dark grout but due to other circumstances delayed cleaning the grout off the tiles till few days later. Now it seems as if the grout has worked its way into the tile but...
  18. G

    Supplementary bonding. Quick question? Photos via name

    Chris yes its a spare. That sounds as if it would save me some work! cheers
  19. G

    Supplementary bonding. Quick question? Photos via name

    Right then Iv got some photos of the cons unit and ensuite. Its got as davey mentioned 100mA RCD one side and 30mA RCD on the other. Im assuming I need supp bonding? If so do I just run a contin 4mm cable from light to sink pipes to rad pipes and then a cable from shower earth to rad pipe.(rad...
Back
Top