Search results

I'm sure there are many threads on this subject, but none appear to answer my question. Apologies for any duplication. I have the above mid position valve fitted into my ‘Y’ plan CH system. It was fitted approx 5 years ago and has operated impeccably until very recently. I can get a...

Thanks. In my situation the cavity at the new door threshold will be approx 12 inches deep from the DPC. How should I proceed to fill this without affecting the thermal bridge? I would have thought in this day of and age there would be a simple, strong and quick and efficient solution to...

I'm about to fit a pair of 4 foot wide french doors in an existing wall. The opening will be created using a diamond cutter and a lintel of the correct spec will be used to support brickwork above. I intend to fit proprietry plastic insulated closers in the horizontal wall sections (building...

Thanks guys.

Thanks, but what I meant was- if I permanently remove the flexible hose for the gas oven (no longer required), do I need to do anything to the end of the gas pipework to make it safe or can I just leave it as is?

I am replacing my gas oven with an electric oven. The electrics are sorted, but I assume the gas oven is connected to its pipework by the normal type of flexible hose. When I disconnect it and the valve on the end of the pipe 'self seals' as it's supposed to, is this enough on its own or do I...

Perfectly clear. Many thanks.

I have a seperate circuit for my hob and oven. I believe the wiring on each to be 6mm2 (measured as 7 strands of copper wire approx 1mm dia for each cable) My questions have arisen as I am about to replace the oven and want to make sure all is OK: 1) I have no problems. The ceramic hob works...

The first issue was the boiler cutting out and not firing up again unless the boiler was swichted off and back on again. My diagnosis for this is the PCB? The second issue was that when HW was on on its own, the boiler would cut out very quickly. Checked wiring and system components, all...

Sorry! Boiler: Ideal Classic NF60 (18kW max) Cylinder: Albion Thermal store, 160 Litre capacity. (using heat exchanger coil in tank) There is a definate heating water temp difference in/out of tank. Had this system in use for approx 4 years, provides great hot water (nothing but praise for...

I'm just trying to get to grips with the one I have and understand why it behaves as it does. Assuming there is calling for heat (both HW and CH), the boilr will cut out very quickly if HW only, much longer if CH or CH+HW. I have Yplan system and pump is set to speed 3. I'm puzzled!!!!

Sorry, as usual I haven't explained myself well. Assuming there is constant demand for heat from external stats, Boiler can cut in and out accoring to internal stat setting. (to protect from overheat?). Is this normal? Thanks.

Thanks, I have read from cover to cover, but these manuals always seem to omit the bit of info I specifically need. So, just to clarify, should he boiler cut in and out according to its own internal temp regardless of calling from other system stats?

An easy one I hope!! My view is... When a boiler reaches its own inernal temperature limit (set by the burner potentiometer?- comments welcome), the boiler shuts down even if the room stat or cylinder stat are calling for heat. The pump continues to circulate water and when the temperature...

Was working fine until 2 months ago. Been living with this problem since then. I'm confident that system wiring is in order. Had a new motorised valve when loft conversion done 4 years ago. Original pump. I can hear it running, but not unduely noisy. Prior to loft conversion pump was on high...

When I had my loft conversion carried out, I retained my boiler, Y plane system and had an Albion thermal store installed. I can't praise it enough!!! Lots of flow, plenty of hot water on demand and what is a simple and effective system. Don't know why there arn't more of them. Hope this helps

My boiler gets it's supply from the programmer (L, N, E). so power for HW and CH curcuits! Boiler will cutout without warning although there is still demand for HW /CH. However, it will only run for 4 minutes if demand for HW only, but if demand for CH and HW or CH only, boiler can run up to...

Thanks all for the info!! I had a theory that my boiler cutting out when there was demand for HW/CH (but HW in particular) was due to overheating and not firing up agin unless the boiler is switched off for a period of time could have been this sensor. Not so sure now as the cutting out...

Firstly, can anyone tell what this is and what it's function is? Secondly, What are symptoms of it's failure? Thirdly and lastly, how easy are they to change (on an Ideal Classic NF60 Boiler)? Thanks

Help please. I have an Ideal Classic HF60 boiler (not condensing or combi on Y plan system) inherited with the house, probably maximun 10 years old that has been reliable and appears to work fine when it does, but intermittantly I notice there is demand for HW/CH (neon on on PCB), but the...