Search results

We went out for a few hours, left the heating running. Came home, tried the hot water without touching the boiler it worked! All works now.

Yes HW light comes on. Pin comes out fully, boiler tries to switch from heating to hot water then the low pressure light comes on.

Yes we have CH but no DHW. The pin is coming out and fully pushing the DHW switch

Same fault for DHW

Thanks. Doublecheck the pump proofing switch, the pin was coming up and engaging the metal of the proofing switch but not pushing it enough make the switch work. Then in the metal slightly has temporarily resolved this, I will order the switch. Still no hot water though, this is definitely...

Yes there is pressure, just under 1 bar. Sorry what is the pump proving switch? Both the CH & DHW demand micro switches seem to work correctly

Hi, I've just replaced the diverter valve diaphragms. When trying to restart the boiler for either CH or DHW, the micro switches engage, the pump runs but the boiler does not ignite. The 'Fault on Pump or Low Pressure' light flashes. Have restarted the boiler a few times, still get the flashing...

Hi, I had a leak where the pipes join the heat exchanger. I removed and cleaner the heat exchanger refitting with 4 new seals. The leak is much less now but still leaking. The heat exchange is flat and securely in place. I can’t see why it’s still leaking. Wondering whether to repeat again...

Yes it’s a light with built leds and our. Connected to a 2 switch in door. I think ericmark is right. It’s a cheap light. As long as the glow isn’t consuming too much energy I’ll leave it as it

They are glowing when they should be off

Our outside lights have been replaced with 2 18w LED lights (LEDs are part of the circuit board) with pir’s. When the light switch is on the lights permanently glow. Will this use much electricity? I can live with the glow providing it’s not consuming too much

Thanks Lucid. It’s wired as per option ‘i’. The cable is plot just before the tv & pvr using a passive splitter as per your first image above. I’m also using cables & connectors as per your suggestions. I’ve removed the splitter plugging the cable direct in to the tv, still get the same...

I’ve installed a booster now get all the channels on all 5 tvs except on the medium run tv. My PVR using the same cable gets all channels but the tv does not get any standard definition BBC channels or radio. The cable is split using a passive splitter before going in to the tv & pvr. I can...

Sorry I thought I did post pictures. The roofer is coming back on Saturday to take a look. I want to be prepared for the conversation

Hi, Our chimney blow down last Friday punching a few holes in our roof. A roofer has removed the chimney and tiled over as agreed. Some of the tiles he has relayed are no longer flat and we still have a very small leak. Should the tiles be completely flat?

I’ve installed a Yagi18k in the loft. using the existing passive splitters I get all freebies channels on the TV with the shortest cable run, no BBC on the tv with the medium run but all other channels and very poor reception on the tvs with the longest run. Next step to install a Wolsey mast...

I was looking at this aerial http://www.trade-works.co.uk/aerials-for-tv-radio-c12/freeview-tv-aerials-c31/medium-gain-tv-aerials-c33/vision-32-element-uhf-high-gain-aerial-p6622. As for the area, we had a strong signal before but are surrounded by a few high trees. This is where we are as to...

Lucid you have been amazing. What aerial & masthead amplifier or signal booster would you fit?

Thanks Sureitsoff? Great find. I mucked up the links. I think Lucid was referring to this Labgear one. Labgear LDA2061LR 6 Way Distribution Amplifier - 4G Filtered Amp For TV/FM/DAB Signals For 6 TVs RED Compliant...

Would a masthead be better? Wolsey WFAV 622 LTE 6 Way Variable Gain Masthead Amplifier with Power Supply Kit - Black https://www.amazon.co.uk/dp/B00PKKTRBI/ref=cm_sw_r_awdo_navT_a_KSXZ7CS7ETX0MTZEQAWF