Search results

I'll check that tonight and let you know what I find. Hopefully, something easily fixed!! D

Zipper Where would I find the PCB on this baby? Is it inside the door? The wiring loom seems to head in there...but can't figure out how to get in to it! :? Btw, the arms were spinning when I hot-wired the motor so is it safe to assume there's not a problem with the two plastic pipes...

Unfortunately, I didn't read your last two posts until after putting it all back together :x so I haven't checked the two plastic pipes but I did have the rubber pipe of, if you mean the one below... However, I didn't find any rubber flap! Just a plastic spigt (junction pipe) that the...

Bummer, I'm going to have to wait until tomorrow before I can test the wash motor; unfortunately, I don't have any spades small enough to fit! But I can confirm that there are definitely no other wired connections to the motor; just the two. :? The resistance across them is 31 ohms Here's a...

ok doke, I'll check it out and get back to you later on. Cheers D

You're right about the water marks...but they're old; several years ago I had a backup caused by an external blockage. There doesn't appear to be any leakage now though. What's the point of two windings? Btw the plug which you can see in the forefront only has two terminals? Across those...

Btw What kind of resistance should I read across the wash pump?

Zipper Having spent £50 already getting the board repaired, you can be sure that I'll not be rushing to spend £100 :shock: unless I really NEED to! D

Is this the wash motor/ pump? And is that a heater to the left of it? If not, what is it? D

Zipper Thanks. Do you suspect the electronic module or was that just a general link for parts? D

Well, there you go, I was thinking that there was only one pump for draining and washing! :shock: So the pump I have taken out and cleaned was the drain pump and, because I have been lying it on its right hand side and removing the bottom and left side covers for access, I've never even...

You're a perceptive one! :oops: I put a multi-meter on it and got infinite resistance so swapped it out. When I did that it happily ran through a cycle (albeit that it didn't spin/ wash) without giving an error. Weird, huh? What's the easiest way to be sure if the pump is running? Can I...

Wasn't too sure how to post pictures on the forum so hope this works... Thanks for all your help so far! D

Zipper Thought that might be the case so, I have to say, I was a wee bit reticent to go and break that seal without knowing I could reseal it. Glad I didn't! Ok, so there are two labels under the door, as follows: ---------------------------------------------------------- 1st...

Zipper Jeez, you know, you're absolutely right! :oops: What a plonker; I've been trying to fix my dishwasher at the same time (both Diplomat integrated machines) and I've got the numbers mixed up in my head. Sorry about that. I have posted a question about it too so, if you know anything...

These are the numbers off the label, if they're any help... 8545 000 15819 33 0602 001158 Can anyone tell me what resistance reading I should get across the terminals of the circulation pump? Any other ideas, folks?

Dishwasher has been playing up. Wouldn't take in water, kept pumping until it gave error (4 flashes). Found failed inlet valve so replaced. Now it runs through full cycle but arms do not spin. Sounds like it's pumping water round the system but just not getting any oomph in it. It is hard to...

8545 000 15819 33 0602 001158 Cheers Zipper! Btw the sump hose seems to be 'glued' into the casing for the tub. Should I be disconnecting it at the tub or are you saying to disconnect the other end of the sump hose, where it connects to the plastic casing for the filter? The hose is...

Thought that might be the case. Pump didn't seem to have enough oomph to spin the washer arms so that makes perfect sense. I'll give her a little clean with alcohol and hopefully she'll give me a whirl! D

Hi Looking for obstructions, I've opened up the pump from my dishwasher and taken out the impeller to make sure it's clear and I've found that there is a greasy coating over most of the recess with a lump of it at the bottom. Now I thought that this type of pump was "lubricated" by the...