Search results

Hi All I have just replaced the element on my Bosch 1200 classixx but after putting back together I now get a loud knocking and excessive vibration when the machine goes to full speed spin. Looks like something is out of balance but can't see anything obvious, any idea's suggestions please?

Hi Had an electrician (well in fact two!) in and they performed all tests and found a broken earth between two sockets, the insulation tests are fine over the effected piece of cable and the ring main in general. Is this an issue safety wise, both sockets are covered by an earth cable but...

Hi I have an mcb which is on my kitchen circuit which is tripping, the installation is about three years old and although I undertook the installation it was was checked and signed off by a local electrical company for building regulations when I built an extension. it has a split load board...

Thanks for your reply, this is what I had actually done but there seems to be a leak into the soffit, I noticed today after a particularly heavy downpour that the water was shooting down the valley and jumping over the gutter, not sure whether this was just sheer volume of water, think I will...

Hi Has anyone got a picture or diagram of how a grp valley falling into an internal 90 degree gutter corner should look when completed correctly. I am getting a leak into my soffit which I am told may be that the valley does not extend far enough into the gutter. Also...

I have a wooden front door and frame. The frame which I had built had a thin plastic strip rebated into the threshold which the back of the bottom of the door closed onto. Can someone tell me what this is actually called and where I can buy one from? The original one was too high and was...

Problem solved, I thought I was trying to connect an excel keypad and it turned out to be a premier. Many Thanks KB

Hi Having a problem with a Texecom LCD RKP which does not appear to be connecting to my alarm panel. I have spoken to and sent a picture of the panels circuit board to Texecom technical support who stated that the RKP should work with my panel (but they are now closed for the weekend!) The...

Hi I want to put in four 50w lights on a twin wire suspended cable system, and have been advised by a lighting supplier that as I wish to use 6.5m spans I will need 2 x 300w Toroidal Transformers. This seems a bit over the top as Ikea sell a set to cover 9m with a single transformer? Can...

Hi I have a Worcester Bosch Camray 25-32 oil fired boiler which has just been fitted, my electrician has wired it up and I ran through the pre comnissioning checks and fired the boiler up and it ran for a few minutes the stopped. The boiler is now not working despite having electricity to the...

Just read back the thread, thanks that answers my question. Regards KB

If you click on the drawing it makes it bigger if this helps, the relay is a maplin 240v made by Beta model BLY6-1C-S-CW. The info at maplin states that it is a changeover set so either NO or NC?? Thanks for the help. http://www.maplin.co.uk/module.aspx?ITAG=FAQ&ModuleNo=37519&doy=8m1#faq

May be being thick but can someone advise me what terminals in my fantastic drawing relate to those on the wiring diagram above please? Thanks in anticipation. KB http://s259.photobucket.com/albums/hh302/rolyberkin223/?action=view&current=relay.jpg

I have had a similar dilemma in a development I am undertaking. The fire vapour and thermal seal caps in the link below have been recommended to me, this is what I am going with you can lay your insulation over the top and also get a vapour barrier which will prevent your roof trusses from...

Yes there are two pumps, one controls two circuits of underfloor heating and the second two conventional heating curcuits (Rads) and hot water. The diagram was suplied by Honeywell Technical Support...

I have a wiring diagram for a four zone heating system which shows a SPDT (Relay), this is to control two separate heating zones. One for two underfloor heating systems and the other for two additional heating zones. The controllers are Honeywell ST9500. Has anyone recommendations for...

I have a wiring diagram for a four zone heating system which shows a SPDT (Relay), this is to control two separate heating zones. One for two underfloor heating systems and the other for two additional heating zones. The controllers are Honeywell ST9500. Has anyone recommendations for...

Rads with legs and four columns, typical school type, I have sprayed again with penetrating oil and will give it a week to soak in with daily doses and then try again with the MAP torch!

Hi In the process of restoring some old cast iron rads, I have shot blasted them and got most of the old plugs out but a few just won't shift!? They seem to be crumbling rather than coming loose, there is nothing to say they have been machanically fixed as I have drilled one out? I have...

Thans for your advice, have not been here for a while hence the late thanks, spending too much time building a house!