Search results

it doesn't feel like a glue saturated layer, its a 1930's house. it doesn't really smell but only comes off with a wall paper steamer after it has been on it a long time.

I am in the process of stripping wall paper off my walls, and have come across a covering I don't know what it is. Can you help? Please see the attached picture, the light brown to the right is backing paper, the tan in the middle is the unknown, and the pinky surface is the plaster. The...

I would and have done in the past battened out to allow the ventilation gap of 40-50mm. Its unlikely you will get exactly 52mm timber to match the existing rafters, so you will have a bit of a gap either side of the PIR board at the face, that if you want to fill will expanding foam. I didn't...

What sort of insulation are you using, if 100mm mineral wool, how about 75mm PIR board as will have about the same thermal qualities.

Ended up just drilling it and tapped a new thread for a new bolt

Whilst cleaning my oven I tried to take out the oven rack guides to clean them. All the bolts came out fine other than one that sheared leaving a thread in there. Question is, how do I get it out, or is there any alternatives to hang the rack guides? Picture is of sheared bolt and how it should...

I have a room in a 1930 house which i am renovating, which has a tongue and groove wooden floor. The issue is that there are 3-5mm gaps between the T&G boards that collect a load of crap and makes it a pain to clean. It is varnished and as part of the renovation i am going to sand it back and...

Having to panes the same thickness causes a resonance known as a coincidence dip towards the higher frequencies, the resonance allows more sound to be transmitted through the glazing at this frequency dip. In regards to the partition wall above having two layers of different thickness board on...

I have an issue that is focused in the area of the kitchen mixer tap, (like this one http://homebase.scene7.com/is/image/homebase/368597_R_Z001?$TMB$&wid=420&hei=420) When i open and close the cold water tap, i get a banging / vibration in the tap mixer. the tap is a quarter turn on/off, and...

cheers, i will see how level it is, my hope is pretty level, joists are at 18 inch centres (450mm) so will be o.k with the 2 x 1" if needed. if not using battens, how would you fix plasterboard to the perimeter walls between joists? is it needed?

We are in a 1930's house with very tall ceilings, the previous owner has wall papered the ceiling. I don't know why they did this, if it was just the fashion at the time or if it was to support the aging lathe and plaster. Anyway its time for the wall paper to go (i hate the stuff). rather than...

Right, just tried the washing machine again and now is working?? On the second fuse I presumed had blown. Double checked the first fuse and that is definitely blown. Not sure what has been going on. Will run it over a few more cycles to see if it replicates the fuse blowing.

The house circuit it is on has a RCD at the consumer box. When the fuse blows it doesn't trip the RCD on that circuit. Sound as though I need to open it up and look for anything out of the ordinary. Not significant water below the washer.

Are you thinking blast marks on a PCB / switch?

Pretty sure the fuse is gone as tried it in another appliance, and a continuity test on a multimeter. Both indicate blown fuse, new 13A fuse in plug (that was deemed good by continuity test) made it work again for another cycle, until I switched it off and blew

Manual rotary switch like this; http://c8.alamy.com/comp/E4M1AN/a-zanussi-washing-machine-control-panel-E4M1AN.jpg '0' at the top is the off switch that it appears to blow the fuse after the cycle.

It seems that when I turn it off at the end of the cycle that it when it blows. I have run out of 13A fuses, so I need to test it to see what happens is I turn it on and off without setting it on a cycle. If it is the door release do you know where I could source a part?

I have an issue with a zanussi zkg7169 washing machine. Earlier I put a load in and it did it's wash no problems. It beeped to indicate it had finished, so I turned the dial to off and pulled my washing out. I went back and did another load to find it was getting no power. Checked the 13A fuse...

i am finally getting round to do this job! thanks for your suggestions. I am going to use 100mm PIR board, and will do as you suggest as measure up first and do the main cutting above ground. Yep i am going to go through the door openings, and put a 900mm concrete lintel above (probably...

cheers for that, so basically at the cut of the joist, span to the adjacent joists. i think that would work as the area is joist at that point is not bearing a significant load, if any (its the cupboard under the stairs)