Recent content by ben3290485

  1. ben3290485

    Chipboard hole in ensuite.

    Thanks for your message. It's really not that big a bulge tbh. I think I will just fill, sand and lay plywood. Would cement board be better?
  2. ben3290485

    Chipboard hole in ensuite.

    Would it be better to use cement board? What should I do about the hole and the surrounding area which has slightly bulged? If I cut it out how could I put something in it's place because there's nothing to screw it onto?
  3. ben3290485

    Chipboard hole in ensuite.

    The chip board which was under laminated in our ensuite has some water damage in one small area where the shower was. I want to lay karndean on the floor. Do I need to rip up all the floor in the room, or can I somehow patch the hole, which I made bigger to find the problem? It's a small area...
  4. ben3290485

    Re-laying Paving Slabs

    I've taken up 6 paving slabs as there was a gap opening up. 3 I have taken up with the concrete underneath (and taken off what I can) and 3 which I have managed to peel off the concrete as there was no way I was going to pull out from underneath. I want to re-use the paving slabs so it still...
  5. ben3290485

    How close can two elbow joints be?

    Ok, Thank you so much for your help!
  6. ben3290485

    How close can two elbow joints be?

    Like this? https://www.bes.co.uk/solder-ring-coupling-straight-socket-copper-15mm-6829/
  7. ben3290485

    How close can two elbow joints be?

    Thanks. If I used two of these connected, what would I then use to connect the male end to a 15mm pipe?
  8. ben3290485

    How close can two elbow joints be?

    Hi, How close can two elbow joints be? I want to put the pipe into the wall and need to create a 90 degree turn before coming back to original direction straight away. I am using elbow joints with solder already in them so I just need to heat up. Can I have them up against each other like in...
  9. ben3290485

    Tiling onto Plasterboard without skim

    What would it be? The house is 15 years old.
  10. ben3290485

    Tiling onto Plasterboard without skim

    I've removed some tiles. Is it okay to re-tile onto plasterboard, without the skim on top? Any tips on what I should be doing? Photo attached.
  11. ben3290485

    Tile Slither

    I've left 6 mm space around the edge of the walls (which is fine because I'm putting panelling and skirting over so will hide) but around the door, can I put the tile right up to the door architrave or does that defeat the point of the space around if one part of the tile is touching the architrave?
  12. ben3290485

    How flat is flat, and have I messed up?

    I have a small downstairs toilet which I am tiling. It's only 1.78m long by 0.8m wide. Where the toilet was there is a small bump in the floor. I am laying 45x45cm so 8 tiles will cover the whole floor. On the right half of the floor the floor is flat, but around the old toilet area if I put a...
  13. ben3290485

    Tile Slither

    Ok. Thanks for your help! :-)
  14. ben3290485

    Tile Slither

    I have a tile slither (can't think of better term) of about 2.5cm x 5.6cm which will be on the left hand side of the door frame. Am I asking for trouble here in terms of it breaking off? I could theoretically cut another tile so that there will be 5.6x 5.6cm square but actually that would be...
  15. ben3290485

    Cut around waste pipe?

    Thanks for letting me know. Do I put adhesive right up the wall or leave a 7mm gap all around the edges with no adhesive there?
Back
Top