Recent content by Hager

  1. H

    Glancing light issue

    Morning, I'm currently decorating my living room and have fitted some wall lights that shine directly on the wall but have been having issues with glancing light, have been applying filler and sanding it down to try and get the wall flat as possible but it's taking ages and it isn't quite...
  2. H

    Covering chimney foundation?

    Afternoon, I removed the chimney from the roof down the ground floor and am now looking to lay SLC over the foundation where it once stood but not sure if there is anything I should do doing with it before covering? The rough concrete in the middle is very soft and I believe to be separate...
  3. H

    Neat SBR help!

    Thanks, I normally do 1:3 but forgot this time round. Luckily its comes off quite easily.
  4. H

    Neat SBR help!

    Evening, I primed some SLC yesterday for another coat but because I like making my life difficult used neat Everbuild SBR instead of watering it down, i can peel it up in little chunks presumably this isn't correct? Have been sanding it off all day, is there a something I can apply or a better...
  5. H

    Water heater expansion vessel

    Morning, Putting a little Ariston Lux 10ltr water heater under my kitchen sink but am struggling on the best way to locate the expansion vessel its only a 600mm cabinet so squeezing it all in plus the waste is tight. Would I be okay fitting the expansion vessel similar to the photo? Aiming...
  6. H

    Blades for cutting kitchen worktop

    Final update- thank you for all the advice i decided to use my router in the end and it cut perfectly for the first pass but i went a bit to deep on the 2nd and it damaged the front edge a little bit but you won't see it so not to much of a issue.
  7. H

    Blades for cutting kitchen worktop

    Damn, what about carefully using a fine blade on a multitool? Its only 28mm thick.
  8. H

    Blades for cutting kitchen worktop

    Thanks for the replys, i was think using a router but not sure my 1/4" will be powerful enough. I won't be using a jigsaw as they are no good for accurate straight cuts. Think i will go with bobasd approach then i don't have to buy any blades.
  9. H

    Blades for cutting kitchen worktop

    Evening, I've got some worktop and up stands to cut over the weekend what tooth blades are recommend? Is it as simple as the more teeth the finer the cut? Going to be using a circular saw for the worktop and a mitre saw for the upstand.
  10. H

    Fuse Board to Consumer Unit?

    Apart from the missing meter, looks like there are two Twin & Earths going into those Henley blocks. :/ also can't see any cables coming out of that service head.
  11. H

    Cutting out part of chimney breast

    Hi, Sorry i know this has probably been discussed many times but.... I have a chimney breast in my bedroom that i want to open up a little so i can put some shelves in it. The chimney is 1370mm wide and 2470mm high, i would like to cut a 900x900mm square out of it about 800mm from the...
  12. H

    3KV 110V transfomer output

    Well the other thought was to change a 16 for a 32A on the transformer and use 32A connectors with the grinder. Jake
  13. H

    3KV 110V transfomer output

    Apologies i'm missing the A. I don't want to join the outlets just want to make sure that i'm not over loading the transformer. I realise that its 3A over the current rating for the Ceeforms but they are quite cheap compared to transformers.
  14. H

    3KV 110V transfomer output

    Hi, Quick question, am i right in thinking that across the two 16A outlets of a 3Kv 110V transformer a total of 27.3A can be pulled for 5mins? Got a grinder that pulls 19A and want to avoid using a 5Kv tranny. Jake.
  15. H

    3 Pin Plug in the bathroom for a Waterpik

    Apologies i missed that bit.
Back
Top