Search results

Thanks in advance

Can't find one anywhere , Bosch deny all knowledge, they haven't got a part number for it , doesn't make sense , surely landfill sites all over the country aren't getting filled with dryers due to these plugs not being available, does It look familiar to anyone ?

Hi , I have a Bosch classixx 7 tumble dryer , recently it was struggling to turn , it has done this a few times in the past ( over 10 years) , I have replaced the capacitor and it has solved the problem ( in the past ) , however today the capacitor has gone again and when I have gone to change...

I've just taken it off , turns out the actual hole is the size of half a brick so over 50% of the vent literally just covered the wall!

Apologies there seems to be an existing post on this , just looks like it's a case of getting a flat blade behind it and lifting it out , trying not to break it. https://www.diynot.com/diy/threads/wall-vent-removal.617321/ Thanks.

I thought about it but then I'm assuming that all the crud in there would then just sit between the internal and external brick and work it's was back into mesh ,

Any idea how I can remove this air brick ?, it's internal and appears to be made of plaster , it's not letting a lot of air in and im going to remove it and clean it , is it just glued on to the face of the wall ? , Id ideally like to keep it and reattach it as can't afford a nice looking one...

Thanks for all the help , I'll have a further look and let you know to hopefully help someone else .

Well I could but it will also turn everyone else on the streets off and knowing my luck a 20 minute job will turn into a day's work

The actual " handle" of my mains water tap has become loose , it just turns , ive removed the little screw and taken it off , the fixing is mangled , however can be turned with a small spanner , now I know that I could put the handle back on and tack it with a small weld , however is there a...

It does have a groove , so apologies , what do I need to do with that ? It's a square groove , I suppose that I could fit a thin round washer into a square groove with some manipulation.

Yeah , was actually thinking of small square of rubber car mat .

Thanks , I did think of silicone however the washer is also to prevent me cracking the sink , I suppose I could always leave washer on and silicone the gap , also poundland is not a bad idea , I was going to cut one out of a plastic milk bottle but I think that they start to biodegrade after a...

I've fitted this new tap , however due to the base of it being a D shape the excess water is dripping through the hole in the sink , I bought the tap as ex display , reduced from £130 to a £10 charity donation at wickes so it was without a washer to go between sink and tap , can these be...

To be honest , Thanks what I was thinking , I'm not trying to con anyone , it doesn't work !

When I moved into my house 25 years ago there was a digital water meter , for approx 10 years my water charges were determined by that , however it stopped working , after a few letters from Severn Trent asking to come and replace it ( bearing in mind this was 15 years ago ) , they stopped...

I've just bought a new prv as combi one is dripping quite badly , I've replaced a few in the past , no problem, is there any reason why I shouldn't use faulty prv to drain system first , If i open the loop and prv would it just run clean water in whilst dumping the old water out , only reason I...

I had a look at the top one in the shop and due to the cut off tap the flow only comes through a small hole that isn't much bigger than the self cutting tap that came with the kit do you think this is sufficient for a pressure washer?

I've bought an outside hose kit, it's exactly what it said it would be ( not suitable for pressure washers) I imagine this is due to the self cutting tap that has the same pressure as my late 40s bladder, I've bought a 15 mm Tee compression to replace it, however I can't find a 3/4 male (...

I've just bought a reconditioned pcb for my ferroli 901, I've had one in the past from the same company no problems, when I plugged this one in the leds just come on very faintly and go off, the clock works and the pump runs but nothing else, is this likely to be a faulty board, all wires...