Search results

You have 3 joists that don't have any post supports just noggins on. Personally I would drop a couple of post supports on these to minimise any slight bounce you get on the decking as there over a 3m span. Up to you if you concrete ones in or rest on a slab . As for the steps depending on your...

Both valves? I only have on iso valve the other is a one way check valve

You could notch the joists and put small timber baton's across. You can get straps that go on the inside of each joist to hold it in place . If you have enough height it might be worth putting sound breaker bars in depending on what noise your trying to reduce

Yes if it's android . You can go into settings and security and remove the password by setting security back to none. If you have a windows version the same is also possible.

Had a quick look and the prv release pipe is dry, took me a sec to find it though as it wasn't at the back of the boiler but was at floor level on the left of boiler outside. So I think this is the faulty valve, what's the screw for? Guess it's a case of fully draining system changing valve...

Sadly tapping didn't work. I tapped a few times then opened iso valve hear a rush of water then after a few seconds just went quiet and pressure never went up. So either it's the check valve or I guess I could have a faulty pressure gauge?

Thanks , yeah I'm going to get someone to take a look at it but myself and brother hopefully can do the work as my mother has little to no funds available. Going to get a friend to remove chimney stack and tile section of roof. Then we will remove the remaining inside chimney stack leaving the...

Thanks for replies, yes I plan to remove the whole of the chimney if possible to solve that problem but just leave diagonal bricks in place that come out of the external brick wall (behold the ones you can see) in regards to the purlin's resting on what I would class as a brick pier to the left...

His guys just been to look at my mums loft and noticed a few concerns. So it's an end terraced house with a single external skin wall in the loft. The two rafters (or are they pearlings)run through a wall to next doors house. Then supported in the middle with a long joist then at the other end...

Thanks for reply. Will try the tapping method in the morning. I guess I can just unscrew from check valve to check the iso valve is working...over a bucket of course. Yeah not exactly the most sound of installs is it. Thin will end up boxing this mess in till we can afford a new one

Hi guys, wondering if you could help. Our boiler pressure is at about 0.5/0.4 and is in need off topping up. Problem is I can't figure out how to top it up. Now about 3 years ago when we moved in the system was fully drained and I refilled then but for the life of me now I can't remember how I...

osb3 will be fine to go direct as its not osb2 but ext grade battons will be better for your circulation

you could use pier deck supports if you dont want to dig , these can come in handy as you just slot post in and secure batton

either thicker screening , or reboard over each of the gaps or board the whole lot in featheredge for a long term fix.

there should be holes in the slotted posts so you can affix a timber baton either side and bolt through then fix you rails 2 this is your best option for a seamless look (on your side) those posts will be really hard to drill so id avoid that. other option is to drop posts inbetween the others...

id attach ledger to the house wall with a few washers behind board for air gap then bolt through. i would usually run your joists the opposite way as typically direction of decking would go from house wall to fence due to foot traffic. joist hangers are fine and would make your life easier...

for got to add in 4 corners there will be 4x4 posts for a pergola like structure over the top

this is the area that needs to be covered from the fence 2.4m across (middle of wall pillar) then 3m from wall out. (basicaly area were 4x2 is crosing). as you can see there is a little paving to the right but i will prob still put a few posts here. dont really want to use 6x2 due to height...

hi guys, built a few decks before but need a little help with this one. deck size is 2.4m across 3.0m in length deck will be raised just off the ground. I will post a pic of the location in a second to give you a better understanding. this deck will also in the future have a hot tub on so...