Search results

It is an integrated one yes, looking for the model number now, could it be that these are not needed with integrated?

Hi All I have a new Bosch dishwasher to be installed and i cannot seem to find the part that goes between the dishwasher and the units next to it (to keep it upright i guess) they are like round spacers which fit in between. No idea what they are called or where they are found, it could be that...

Many thanks, i think i will make a hole in the bottom of the cab then out through the plinth at the bottom, hopefully will not be seen. Question though, the hole in the unit is 150 and i have a reducer taking it down to 120mm. What size pipe would i need to go on these? brain is saying 120mm and...

I do have an extractor in the wall to comply. What i need currently is a decent looking output vent I can place on the outside of the island, not too sure whether to go out the side or below it and then out through the plinth piece (150mm). The pipe is 120mm so this is possible, just need some...

Hi Putting together a kitchen and on the island we have a Faber Fabula downdraft extractor fan, one of these things that goes up and down when you are using the hob on the island. Looking at the instructions, I thought I was buying something that did just that, rise up and down and used...

Sorted, there is a middle line :)

I have the guide here and can see the top arrows so I guess that the paper template sits right at the top of the door. Down the sides there are the markings for the holes I need to mark/drill but the paper is slightly smaller than the door so I am not too sure how to position it to get the holes...

Hi Had lots of help already in here so trying with another question. I am currently installing the other side of the kitchen which is Walk In Larder > Integrated Dishwasher > Sink Unit > Bin Unit > Wall The walk in larder has a 'slab' that needs attaching to it (full height) As there is a...

Hi All Trying to install my kitchen and have a Bosch integrated dishwasher. I'm not too sure if there is a cabinet that houses this, i dont think that there is and it just sits in the 'space' as it is quite large. What i am trying to work out is where it needs to sit. I have to put on a door...

I've just ordered some of these :) read it as 200mm

I think it is the right way up, there are screws to fix to the sides and also a lock bar at the bottom which gets pulled down

I have found a video of the installation of this item (a few in fact) from the Infinity section of the installation guides on the Wren website. It says (to paraphrase) draw a line at the top where the cabinet is going to end up (this would be in line with the other units already installed. Then...

I think that the rail is the best solution here, worried about using the anchors as I don't know if they will open because of the celotex as it is quite dense. The unit is 800 wide, can you get longer rails? I;ll have a look, that way I should be able to at least screw it into two studs direct...

Hi I am in the process of installing a Wren kitchen which is proving very tiresome. I am currently trying to put up a couple of wall mounted cabinets above a worktop. The brackets supplied come with no measurements and the installation video says that need to be installed at 120mm but in reality...

Many thanks for the vid, yeah looks like they go flush with the doors. i'll sort out the filler bit later on i think, pretty sure it needs to be on the same level as the doors too.

Yeah i know what you mean, i am trying to work out where the cornice (i think thats what its called, the big long bit that goes across the top of the run) and whether this goes flush with the doors or in line with the body of the cabinets. The end panel i have put on goes flush with the doors...

I've managed to get around this one by cutting a hole in the back, screw through it and then cover with a cap. The next problem (opportunity) i have now is in the filler strip that is in the pic, i installed this flush to the body side of the first tower ie not the door. Looking at it now, i am...

Its a bit of a crazy situation really, i am sure that people are installing these every day of the week. Was speaking to someone earlier who has a tower unit and what they did was to install the bracket upwards so it goes vertically from the top. I guess you wouldn't be able to see it because of...

I think i will cut a 32mm hole and then use a 35mm hinge hole cover to cover it up, just hope i can get the right colour

Yes i think those are the best solution I spoke to them, 47 minute call, said that the brackets go in the top corners. I said that there is no room to include but they said that the brackets have to go in the top corner, this went on and on so i had to give up in the end What i am going to have...