Search results

That was my initial thought, then i thought of actually putting the switch in the office That way I only have to do one run from the kitchen ( it involves a tortuous route under decking etc) And we can also have a hard wired connection in the office. Sadly the wire cant really go though...

Sorry but hijacking this post a bit I am in a similar situation to the op I have a router in the living room with a cat5 run through the house to the kitchen ready to be extended to our summerhouse at the end of the garden. (40m) We have now decided to build an office halfway up the garden (...

Bit unsure about your reply as the whole post was about it not being perfectly square but whether the amount was deemed to within "tolerance"

Thanks for the reply, yes I know that i need to do that but I am hoping I can know what to do prior to this ie if I run the 2.5 then I can physically run it down the garden and into the office during my office build. etc. regarding what you wrote does that only apply if you swap over the cu and...

Sunray Thanks for that, but I presume the over riding factor for that is to have 6mm cable- if i stuck with the 2.5 could i run it from a breaker? I suppose its a case of buy new cable or buy a new cu for the summerhouse ( though, to be fair, I would use the old one in the office)

YEP it has done that a few times!!! it was inherited when we bought the house. what would you suggest as an alternative?

Sorry should have said UPVC

Thanks harry is that armoured T&E as the other piece I have measures about 13mm (maybe less) but says 2.5mm. If the original cable is 6mm then I presume there would be no problem with changing the cu above to one with 3 breakers and having a 32a breaker to feed the office?

Hi all Me again. I am building a summerhouse and due to the uneven ground we have lost about 200mm on height before we start. by the time I have laid the frame (4x2) 18mm osb on the floor, built the stud wall ( again using 4x2) a length of 4x2 to create a slope then 6x2 for the roof and 18mm...

Why not My mistake the size is 4.6 x 2.4 so the diagonal should be 5.188 my measurements are 5.17.5 and 5.185 ( measured one handed so not mm accurate! so still 10mm out but I cant see that being too much of a problem Thanks for all your help

I did indeed but I am pretty sure i was reading 5.17 on the diagonal but maybe it was 5.27. But thanks again

5.3m ?? are you thinking of the diagonal? But thanks anyway That reassures me alot

erikmark thanks for the detailed reply In the house I have the 32a mcb with a RCD covering all the breakers the I cant see the size stamped on the outside of the cable leading up to the summerhouse but it does have bs6726 stamped it is about 15mm wide, The additional cable I have is a 2,5mm...

Hi all I have just finished building the base for my summerhouse. It is 4.7 m wide with a depth of 2.4m It is constructed using 4x2 with a centre joist running left to right in the middle and joists front to back on 500mm centres. I have just laid it down after fully constructing it ( joints...

Edit I have just checked and the breaker in the house is actually 32a

Thanks for the replies I am now wondering if its possible to put another breaker into the consumer unit and then run the swa from that to the office? It does mean a longer run but it saves splitting the cable and running it under decking etc

That is a very good question I will have a look and see if I can measure the fitted one. The existing run is about 20m Which actually brings me to my next question. If the cable is of sufficient rating could the main breaker be swapped out for a 32a?

Can I ask why is that. The main reason in installing the consumer unit was to be able to isolate the lights and power circuit and in the hope that should anything trip, then it will trip the board in the office rather than in the house. and since you have to "convert" swa to twin and earth at...

Hi all I have a summerhouse at the end of the garden which has a power supply coming from the house via a 16a breaker and armoured cable leading to a consumer unit in the summerhouse. We are building a home office in the middle of the garden. I am hoping to run ( or rather have run) power to it...

Notch, Many thanks for the reply. Would the cement boards not to the job of sheathing as well as cladding? I would definitely use strapping as well. I was thinking of using no more ply 18mm T&G to make the joins neater and stronger.