Search results

Carb linkage is free & not jamed. Carb apart & was cleaned but doesnt mean its 100%

Petrol & oil mix. Plug seems ok but maybe dry

When i removed the carb i unscrewed the fuel cap then blew down the pipe & could hear it in the tank so i would say no its fine

I started the saw yesterday & let it run a while & all was fine. Today I went to the job just down the rd but it was a pig to start. Once started operating the trigger didn’t give me much hope with what I could hear. It then sounded fine & I started to cut some logs but after say 5 minutes I...

British gas came out. He changed the stat & receiver for the newer type which is touch screen. Paired in minutes. Boiler fired up but after 10 seconds etc started to die down. Did all his checks etc & then connected a hose to a spout & then into the bucket. There was no water moving...

I press the bottom right button on the receiver & it lights up green then pretty much straight after i hear the boiler start to hum etc. This now has been humming for a few minutes but the green light that should be lit by the flame logo on the boiler never lights up. The green light on the...

Pressing the button you mention the white / blue flashing light changes to orange. I press the same button again at the bottom & turns green. I hear the boiler fire up but after say 10 seconds it goes all quiet

Energizer max I’m still getting the white / blue pairing light on or flashing when I press the button you mention I press that button you mention & see a green light but no boiler flame green light

Just bought & fitted 4 new AA batteries. I found instructions for pairing. Press & hold button on receiver until orange light flashing. Done that. Press button for say 10 seconds & the orange light will turn white / blue. Done that. Now I fit batteries in stat. I see on stat screen a boot...

Morning. I have the boiler shown in photo. Had to get up as it was cold & could see we had no heating. Red battery light on controller flashing so I replaced batteries with what I had. Red light no off. Controller shows ON but boiler isn’t doing anything. I pressed reset & boiler starts...

Last night the ice was thawing & i was able to remove it. I had left the door open until this morning where i then gave it a wipe around. All drawers refitted & the tray at the back was nearly full of water. Ive now removed that water & switched it back on. Now been on 4 hours & will replace...

Inside the 2 windows are say 1 1/2 inch of ice. The 3 arrows blow are ice left to right so maybe under there. Food now in friends freezer. Door wide open but adding a bowl of hot water in the freezer to speed things up will the heat go up into the fridge as this wasnt removed just the frozen food.

So the slope will be the other side of that rubber hose I see above the tray

Yes frost free & I did look at other posts. Most advise the issue but I was asking as to where the drainage hole / pipe etc is located just in case I could remove something but sounds like the issue is a build up of ice.

With regards drainage to outside the freezer is that the black rubber hose that I assume delivers water to the tray above compressor ?

I have a INDESIT fridge freezer which the other day i was unable to pull out the bottom drawer.When i did manage to get it out i could see ice below & that was the issue as to why it was stuck. I removed the ice but after a couple of days its back again. I read about blocked drain hose but not...

That looks like the bearing or bush spacer for the motor as the fan blade then is installed. The photo of the rear drum spindle matches what i have.

Ive now ordered a genuine bearing as advised. Thanks

Item 423 is the whole rear metal panel Why would I change that. It’s to expensive to do that & that doesn’t explain why the bearing has failed. The rear metal cover just has a hole in it which the drum spindle passes through. Just can’t see why you advised that ???

There is the main plastic cover that hides all behind. I remove the 2 screws then i see a circlip through the end of the drum shaft. I remove circlip & pop off a circulare metal part like a wine gum sweet. Once that is removed i can then just pull off this peardrop part