Search results

Get these: https://www.toolstation.com/shop/p68683?r=googleshopping&rr=marin&utm_source=googleshopping&utm_medium=feed&utm_campaign=googleshoppingfeed&gclid=EAIaIQobChMItcLNmayM3wIVhrTtCh0G4QZzEAQYASABEgI1t_D_BwE Mark everything up and hanging correctly, then take the brackets off and chisel...

Yes

Thanks both - this did the trick with some small adjustments to the cupboard.

Cheers Terry. I just provided the links as a best representation of what I’m working with so might not be those exact fittings but appreciate that’s all you’ve got to work with as well :-) If there’s nothing that will fit into that side fitting then I’m sure I can swap for what you’ve...

Thanks Terry - apologies not sure if you edited your post but I didn’t see the last sentence when I first viewed the post. I’ll have a look again tomorrow but not sure there is room for that setup youve suggested. Was hoping I could just use the existing connection.

Thanks - OK fair enough. So what I currently have to work with is this...

Hi all - I’m plumbing a dishwasher in for my brother, he’s currently only got a washing machine and therefore a single waste fitting into the traps under the sink. I bought one of these to enable a double waste...

Wait until someone with more knowledge can confirm but I’m sure my grandparents had the same if not very similar type of valve on their old radiators. I think if you unscrew the cap to the left there will be a hex which in fact can be used to balance the radiators. Don’t think you can drain...

Hah, yes, but have some pipe covers over them so don’t look too bad, but not copper I admit :-) Looks like pipe even too close to skirting to get an enlarger on. What about something like the elbow below going into the rad pointing ‘back’ to the wall, with the valve/TRV going into this being...

Quite. Jut realised, having wanted to swap a single to a double radiator, the pipes are too close to the wall to meet the double rad valve. Done things backwards, the floor on was only done last year so can’t modify the pipe to move it out. Any bright ideas or or am I stuck with a single? Need...

Nice one mate thanks a lot - there doesn’t appear to be anything printed on the pipe itself (it’s grey rather than white), may have rubbed off, but I can see on some of the push fit connectors on the water pipework are have JG logo, so suspect that’s the one.

Thanks, sorry should have said it’s plastic. Will try and reuse but in case I need new - is this what I need? https://www.screwfix.com/p/flofit-flo-fit-fxi1o-pipe-inserts-10mm-50-pack/55253

Hi - replacing some radiators on 10mm microbore pipework, the valves I am planning to use (opposite to TRV) are these: https://www.screwfix.com/p/chrome-angled-radiator-valve-10mm-x/51257 Will I need to use plastic inserts with these on the plastic pipe? Or copper? Not sure what type of...

Edit - ignore guys, wrong forum.

Thanks, so you’d say the Danfos RasC2 over the Drayton TRV4? The latter looks better :-)

Also could someone tell me what the difference between a liquid and wax sensor on a TRV? Looking at these for my 10mm microbore: Liquid: https://www.screwfix.com/p/danfoss-ras-c-white-chrome-angled-angled-trv-10mm-x/33140...

Thanks - house was built in 2000 and these are he original rads - would that be classed as ‘old’? Fortunately (or unfortunately!) pipes are microbore so 5mm each side will be fine.

Looking to replace 6 radiators in my house so just measuring them up and was expecting them to be all multiples of 100 both height and width (e.g 600mm x 700mm), but all the heights of mine are 520mm, 620mm or 720mm. Is this normal? Also, do you measure the width to the valves rather than the...

Bought 2 black-out blinds a year ago and another 2 exactly the same the other week. Brilliant service and for me the price is very reasonable. I’ll never buy and adjust blinds again.

Only thing I’ve found of any use is some white silicone. Try to flatten off the hole first by pulling a piece of hard plastic across it in all directions, as usually the edges are proud. It won’t be perfect but your eye (and therefore anyone else’s) won’t be drawn to it at all.