Search results

Yes I have a spirit level the problem if I tighten it up at the top I here is a gap at the bottom and vice versa I join two 800 units together

My kitchen wall is not square I know I hide imperfections with the corner blank by scribing in the wall How do you go about tighten the support brackets though. Do you tighten on the brackets and allow the gap at the bottom that will be covered bu the end panel or you allow equal gap top and...

I’m installing a Wren kitchen and I have two 800mm wide wall units. Do I use a divider or not? Inside the flat pack there are three planks I can cut to size if I need to fit one( I think they were there for protection ) Wren provides middle supports for the 900-1000 wide units but not the...

This Fischer pack came with brass screws that’s why I asked. The stainless steel screws I buy from Accu screws are getting rounded if you push them and are not as strong as steel as I had some of them snapping when I installed curtain poles. You can get marine grade ones but this only improve...

I’m wondering what you usually go for securing cistern onto tiled wall. Brass screws or stainless steel. These are screws are virtually inside the cistern tank

I chipped the toilet cistern lid. Is there anything you will recommend to fill and re enamel so I don’t have to replace the lid ?

Thank you both, you got me in the right direction I think I might try this one :

I guess I can cut the pipe shorter and use one of these But does anyone do a compression 32mm to a blank 32mm pipe coupling ? So compression on one side and pipe looking on the other. Something like the Floplast but no bent , straight instead.

I seem to have cut the 32mm basin waste pipe too short. Is there anything I can do to extend it by 22mm? I tried two different traps and they do not fit now I used a p-trap with an extension but the extension now is too long. The bottle trap was ok before I cut the pipe by a bit but now the...

The floors, we generally remove the floorboards and ply with an 18mm ply first. The bath is screwed down well, there is always a week area a bit behind the drain hole which is usually where you are standing to have a shower, plus I'm not impressed with overall rigidity despite all the prep. My...

I am looking for the most steady bath for up to max £400. I do not want a steel bath as it is for a rental but looking for something steady. Tried various make before like Ideal Standard, Carron and when you walk in the bath you can feel the floor moving slightly despite all the brackets and...

What size is the hole for the bathroom pillars. I’ve got the feeling my plumber is been drilling these too big. The hole is just shy of the size of the pillar!

I just inspected one of the rentals and the bath screen only after 2 years has gone very stiff. Also the frame looks so flimsy I think my plumber used the cheapest B&Q one! I have already purchased a Mira one but I did lubricate the existing one with white lithium grease and it started moving...

Wow! thanks so much. The doors in our factory weight possibly more than 50kg made of acoya wood and have no architraves. They have just been fitted with a square frame. They have 4 hinges. Yes the fire officer who inspected the place noticed the expandable foam and said exactly the same thing...

Ok thanks for your responses. I will route the doors then. Can I just check I want to install smoke and fire seals so is the aim for the hair of the smoke seal to just touch the frame of the door. I’m asking this so I calculate the depth of the routing after measuring the gap between the...

I have 5 doors to do this week fitting 15mm intumescent strips. I’ve been using a router for door hinges for years but never done an intumescent strip. My question is if I want to grove the frame rather than the door how do you finish the end of the grove where the router body stops from going...

I’m having the garage wired by my electrician. But he wants me to dig the trench. At the end of the trench there is concrete, how deep do I need to go into concrete as it is such a pain trying open a grove for the Trunking. It is a 4m armoured cable he uses. He told me it doesn’t matter how...

I’ve got a 60s garage with asbestos roof. Can you paint the external walls? They look like broken brick and stones surface. Do you need to prime them with anything first to seal them ?

N in

I would PVA the lot and you can also use some wide skrim tape and plaster with bonding first then multi finish. Use the remaining of the edge as a guide with a long straight edge to create neat corners. The remaining of the corner does not seem to have a bead so you basically restore it back to...