Search results

Hi is it easy to remove this 60/80A fuse to cut supply to the CU? Simple as cutting holding wire and pulling? cheers daljit

Cheers. Will go perfectly with door frame 47x95mm.

Hi Erecting a small internal wall (8ft x 5ft) with doorway and plan to use 15mm fire line on each side of studs. Door frame is to be 100mm to tie with existing. Was aiming to use C16 grade but not sure what size? Ideally, I’d have 47mmx68mm as that leave couple of mills for skimming either...

Just found out fan works when both door switches are activated. Anyway, will reassemble and see if it works even tho I’ve not done anything to it other than clean a little.

Hi Siemens KG30NVW25G fridge freezer is cooling the freezer, not the fridge, which sits above. I’ve removed inner rear panels and there doesn’t seem to be any obstruction to the shaft leading from the cooling pipes in the top part of the freezer to the fridge. It’s now been defrosted. When I...

Great, just what I thought. Thanks.

Hi I’ve read guidance about zones in bathroom. just want to check before proceeding. Am I allowed to use a standard light (ceiling rose, cable, bayonet fitting) in my bathroom if the bulb is at a height of 2.5m? Ceiling rose at 3m. The light would be positioned above one end of the bath. I...

Thanks for that link Ken. A quirked staff bead - who woulda thought! Ive not been able to open all the photos on that thread (on my phone) but it seems the OP opted to mould the corners out of plaster, rather than stick with wooden beads. Other posters suggested quirk created by channeling out...

Ken, thanks for the response. Hopefully photo uploaded this time. Yes, the wall’s been repaired over the years with polyfiller and like. I’m thinking I’ll need to chip away old plaster/polyfiller before skimming otherwise skim at corner would sit proud of the baton? yip, I know the corner...

Hi I’m renovating a traditional tenement and looking for advice how to re-plaster an external corner, which had a rounded wooden baton running vertically. See photo. I’d like to keep this baton if I can, skimming the walls on either side. However unsure how to do this. I like the rounded...

I was thinking of connecting pan to the branch of a 110mm tee, running pipe along the floor and outside. Then, using below, connect 40mm pipe from bath to the tee...

Hi I’m installing a new bathroom in a 4ft x 10ft space, with window and two existing outlets beneath it at one end. Outlet 1 was connected to a basin and is 18” above suspended timber floor, leads outside to a cast iron stack. Outlet 2 was connected to a bath and runs from above floor level...

Sorry, yes photo is lying on its side! The knuckle with white plastic leads to the pan, black pipe runs vertically through the tenement. I’d love to angle grind but unlikely to get round the back. Flex seal cap looks an option - I’ll ask merchant what plugs they have.

Hi just to post an update. My heating engineer fitted the flow switch and it did the trick. Shower seems to be working fine now.

I was planning to box in the cast iron down pipe, so capping or cutting the current link to the WC as short as possible would be the ideal. cheers

Hi I’m removing a WC for good, and need to cap the soil pipe. My question is, in the photograph you can see a brown (cast iron) collar that seems to connect plastic to the (cast iron) soil pipe. Do I cap with the collar left on, or if I need to remove it, how is this done? cheers Daljit

That sounds a good approach to me. However it’s a ground floor tenement flat with considerable weight above which is I’m guessing why it seems so high spec. Beams will sit proud of the removed wall so will be a wider box on show. This will encroach cornice in one room I’m imagining, which might...

Hi I have a building warrant and am now just starting to study the drawings submitted by my architect and structural engineer (SE). I plan to remove two walls of 2.5m and 1.5m; one is in the kitchen and the other in the bathroom. By removing the walls I will be making what are two compartments...

Sorry, I should’ve said. It’s an eBay shop called boilerspares with 33,000 sales and a 99.8% positive approval rating. It only sells new parts. Besides, it may not fix the fault. It might be smthg to do with the plate exchange, as someone above suggested. And a plumber I spoke to y’day, who’s...

From investigating further... i think the issue is with the DHW sensor, which i believe may also be known as a (magnetic) flow switch. It forms part of the hydraulic inlet assembly (about £100), which Baxi (i'm told) don't sell separately. However, found it on ebay for £15 so will see if that...