Search results

Thank for your advice. I have looked at the Haynes video which shows its a normal right hand thread. Before I start an oil change I go for a long run to get the engine hot, unfortunately this did not help with the problem.

Hi Doing an oil and filter change on my 2018 Micra K14 engine. Does anyone know of any method to remove the plastic oil filter cover. It's so tight that it's distorting the plastic nut on the end of the cap. I feel if I put any more pressure on it, it will just round off the corners. Why do...

As some who's last boiler was a Thorn Olympic and in 30 year only had to change the thermocouple, maybe I'm being a bit hard on Atag. I know there is no comparison between the two boiler, but I don't want to start a conversation about simple Vs efficiency so I will just thank everyone for their...

I think these forum's are here to advise and inform. By posting my the negative experience I have had with this boiler it let's anyone looking for a boiler to take this in to consideration when choosing what make of boiler to purchase. I know I always look at what other people's opinions are...

This was more expensive than quoted for other boilers eg Baxi. Yes all boilers can go wrong, but after just a few months, bad quality and bad quality control.

I have a Atag ic Economiser Plus 27, I woke up this morning with no hot water. I contacted Atag they suggested that the flow sensor was the fault. I feel that I have been cond, the boiler is only a few months old and I get a problems, I wish I hadn't take my installers advice to spend an extra...

I'm would like to thank everyone for their advice. I think the consensus is to leave the heating on a low setting, sounds like good advice too me. I take on board the point not having the under floor pipes lagged is wasting money, but without wrecking my house taken up the laminate flooring...

Thank you for your replies. My insurance only requires heating if my house is left more than 60days. Yes the frost protection is on for the boiler, I'm not sure if this will stop pipes freezing in the house. I have not lived in this house for long and only had access to the under floor in one...

I have a Atag ic Economiser 27Plus boiler, can I turn off my water at the mains without causing any damage to the boiler. The boiler is in a cold utility, will the boiler frost protection keep the boiler safe. Should I leave the heating on constant at a very low temperature, say 12 Degs. I will...

I think I assumption was wrong about the lock shield valves, the house was not warm when I got up this morning, again house did not warm until midday. Watching the ch temp out, first thing this morning it was showing around the 40-45deg mark most of the time, occasionally reaching it's requested...

Unfortunately l have no access to the pipework, without distroring my laminate flooring.

First of all I must thank everyone, exceptional support from all contributors. After following your suggestions, I think I have discovered the problem. As I said I was going to open all the trv's and Lock shield valves. I monitored the temperature in and out of the boiler (thank you JonathanM...

Radiators all heating as they should, did have to bleed only one, all rest heating evenly.

Yes the installer flushed the system. I have opened the lock shields and trv's, l will monitor the flow in and out of the boiler when the heating is turned on in the morning.

If thing don't improve looks like the path I will take

Good deduction, I will check the lock shield valves and open the trv's to maximum, see if that makes any difference.

I don't get any fault codes not 104 or anything. Thank you for the input, but in my case I have a radiator system, and I have good water pressure.

Thank you I will follow your suggestions

The thermostat boiler icon is showing most of the time. The flow is 59deg and return 48drg. It is now 2:00pm and the radiators are finally hot, so I will have to wait until tomorrow morning and do your checks when the system is starting up.

What temperature differential would you expect between temperature out and temperature into the boiler.