Search results

Brand is LAP chrome effect fused spur, installed approx 5 years ago. Will fit a white MK fused spur instead. Is it safe to run back to back loads in the dryer? or is it best to be safe and allow the dryer to cool down after a cycle before running another load?

I assumed it was fine as the neon light came back on and so did the dryer

Chrome plated fused spur switch arching/screeching noise. Ran the condenser dryer, first load was fine. Ran a second load immediately after, 20 minutes into the cycle the dryer switched off. I looked at the fuse spur, the neon light was no longer 'on' despite being in the on position, the...

It's been 48 hours since I fitted the rat flap and so far the CCTV has not captured any rat activity, I think it's safe to say the rats have been entering via the ground floor WC waste pipe. I purchased a cheap inspection camera which connects to your phone and managed to get the camera below...

After several days of monitoring via the CCTV camera, I am pretty certain that the rats are entering the suspended floor via the ground floor WC as they are constantly returning to the area where the WC is located. They are huge and clever, I laid down a rat trap underneath the suspended floor...

Looks like I may have missed the mark :( Just past 4am the CCTV camera triggered a recording and captured footage of the rat, sniffed around for a few seconds before disappearing underneath the floorboards. Pic attached It appears it's come through elsewhere, not the hole I suspected! We...

Update I've excavated more of the area, removing the expanding foam and can see a deep hole in the corner which passes beyond the brick work of my property. Upon closer inspection I can also see the waste pipe which connects to the man hole in my neighbours garage! I've tried to open my...

I've been hearing noises for the past several weeks and finally suspect the rats are getting in via the soil waste stack as I could hear the noise coming from the base of the stack. Pics attached I removed the floorboards and at the base of the stack I could see droppings and a pungent smell...

Update Lowered the striker plate strip approx 7mm, door now locks perfectly! If you're hinge doesn't have height adjustment this could be a solution for others that may encounter a similar issue

As I can't raise the height of the door, I need to lower the striker plate so it aligns with the door. Raising the striker plate won't work as I can't adjust the door

I'd say the hinge side, as soon as I lift the door it engages and locks fine, otherwise it doesn't lock. Thinking to either pack the hinge or lower the striker plate

Had a look, the bottom is just for compression Need to adjust height approx 10 -15mm what would be the past way to do this? Can you add packers to the hinge?

True! I think the door has dropped, hence why it is catching, how can you adjust the height?

I'll give it a go, making small adjustments as I go and test it as I go along, will report back. Didn't realise until later that rosewood coloured doors are notoriously problematic when it gets hot. White doors never had a problem! Many thanks!

So all i need to do is adjust the allen bolt, given that the door is catching against the frame and difficult to engage the lock I will need to adjust the bolt clockwise? I do hope this works I'm at my wits end, looking at the metal strip, the strike plates are all over the place, they are not...

We've had several locksmiths out paying a small fortune over the years but whenever we have hot weather the door starts to play up! The door is catching against the frame and we are having to exert a lot of force to lift the handle up in order to lock the door, to the point where I think we'll...

Planning on installing the fence this summer, I mentioned I'm intending to install a 6ft fence with a 1ft gravel board. Problem is, I would be 13cm over the 2m regulations. My plan is to therefore bury 13cm of the concrete gravel board into the ground and then backfill with soil to ensure I'm...

Currently have an outdoor light which is PIR only but very unreliable and temperamental. I've had a few which have all been the same. Does anyone have any recommendations for a reliable/ heavy duty commercial spec if needs be (for domestic use) photocell and PIR outdoor light which is dimmable?

I just hope it's not dangerous and not a risk of causing a fire! What would cause the noise and for it to leak tar?

Earliest I can do it will be on the weekend as away, what would be the noise? Is it dangerous?